Vitek VT-2333, Инструкция по эксплуатации

Страница: 4 / 32

4
ENGLISH
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage under
cold (winter) conditions, it is necessary to
keep it for at least three hours at room tem-
perature
.
There may be water spots in the air humidi-
fier, this is normal, as the unit has undergone
factory quality control.
–
Unpack the unit and remove any stickers and
package materials that can prevent the unit
operation. Check the unit for damages. In
case of damages do not switch the unit on.
–
Before plugging the unit in make sure that
your home mains voltage corresponds to the
power adapter operating voltage.
Notes:
–
Use the humidifier at room temperature from
+10°С to +40°С and relative humidity less
than 80%.
–
Water temperature should not 40°С.
USING THE AIR HUMIDIFIER
–
Remove the lid (1).
–
Remove the water tank (3) and fill it with water,
do not exceed the maximal level mark “MAX”
on the scale (4).
–
Turn over the body (10), insert the power
adapter (12) cord connector into the socket
(14), place the cord into the corresponding
groove and set the body (10) on a flat steady
moisture-resistant surface.
–
Place the water tank (3) on the body (10) and
cover it with the lid (1).
–
Wait till the process chamber (7) is filled with
water.
–
If you want to use the aromatization function,
press on the air inlet grid (13) and extract the
aromatic oil container. Add some drops of
water-soluble aromatic oil on the felt insert
and install the container back to its place,
press on the grid (13) until the lock is tripped
(pic. 1).
Notes:
–
use water-soluble aromatic oils only;
–
if you are not going to use the aromatiza-
tion function, remove the felt insert from
the container, wash it with water and neu-
tral detergent, rinse, dry and install it back
to its place.
–
plug the power adapter into the mains socket.
OPERATION MODE CONTROL BUTTONS
“Mist” release ON/OFF/intensity button (15)
–
Press the button (15) to switch the unit on,
to set the “mist” release intensity, repeat-
edly press the button (15). The “mist” release
intensity is indicated with light indicators (16):
«
• » – low intensity,
« •• » – medium intensity,
« ••• » – high intensity.
–
To switch the air humidifier off, press and hold
down the button (15).
Timer setting button (17)
–
Press the button (17) repeatedly to set the
timer within the range from 2 to 12 hours (with
2 hours step); the timer operation time will be
shown with the light indicators (18).
–
When the set time is reached the unit will be
switched off.
–
To switch the timer off, press the button (17)
until the light indicators (18) go out.
Switching the water tank illumination on/off
–
To switch the water tank illumination on, press
and hold the button (17).
–
To switch the illumination off, press and hold
the button (17) again.
Low water level indication
–
When the water tank (3) is empty, the unit
will be switched off and the light indicators
(16, 18) will be flashing.
–
Switch the unit off by pressing and holding the
button (15), remove the lid (1) and the water
tank (3). Fill the tank (3) with water (see the
chapter «Using the air humidifier»). First install
the filled water tank (3) on the air humidifier
body (10) and then install the lid (1).
–
Switch the unit on for further operation.
IM VT-2333.indd 4 10.01.2018 17:04:06