D-303360 CLIP SMA Installer's Guide
1
CLIP SMA
Wireless Curtain-Type Infrared Detector
Installation Instructions
1. INTRODUCTION
The CLIP SMA is the smallest and most elegant wireless curtain-
pattern PIR detector for indoor use and designed for easy
installation. Its function is based on new and sophisticated,
patented FM data acquisition and digital signal processing.
Modern technology is used to include 3 different detectors in a
single case, each programmable for optimized performance at
the specific mounting location. This results in better catch
performance and virtually no false alarms.
The superiority in performance of this detector is achieved by
applying an improved version of the patented
True Motion
Recognition™
(TMR) algorithm. This advanced motion analysis
method allows the CLIP SMA to distinguish between the true
motion of the human body and any other disturbances that cause
false alarms.
After detection, the detector disarms itself to save battery power.
It rearms (reverts to the ready state) if there is no subsequent
detection throughout the following 2-minute period.
The CLIP SMA includes the following features:
Very low current consumption
Microprocessor-controlled temperature compensation
Sealed chamber protects the optical system
Front cover tamper switch
White light protection
Elegantly styled, sturdy case
Detailed coverage patterns and mounting alternatives are
illustrated in Figures 2 through 6.
Figure 1.
CLIP SMA General View
Figure
2.
Wall-Mount Curtain
2.4m
Figure 3.
Ceiling-Mount Curtain
Figure 4.
Overhead Curtain
This
side
up
Figure 5.
Curtain / Pet Alley
OPTION A
OPTION B
DETECTION
CURTAIN
Figure 6.
CLIP SMA on Internal Doorframe
2. SPECIFICATIONS
OPTICAL
Detector Type:
Dual-element low noise pyroelectric sensor.
Number of Curtain Beams:
2
Mounting Positions:
See Figures 2 through 6.
Range Settings:
Long (6 m/18 ft), Medium (4 m/12 ft) and Short (1.2 -
2m/6 ft) (Jumper-selected).
ELECTRICAL
Internal Battery:
3V Lithium battery, type CR123A. For UL installations,
use Panasonic, GP or Sanyo only.
Nominal Battery Capacity:
1450 mAh.
Battery Life:
3 years (for typical use).
Note
: Inability to connect with wireless network, or wireless link quality no
higher than 20% may significantly reduce the expected battery life.
Battery Power Test:
Performed immediately upon battery insertion
and periodically every several hours.
Microprocessor:
8-bit, low power CMOS.
FUNCTIONAL
Visual Indications (red LED):
LED lights
for about 3 seconds upon transmission of alarm & tamper
messages and upon motion detection in the walk test mode.
LED flashes
during the power-up stabilization period (approx. 2
min), or after restoring the cover (by pressing the tamper switch).
LED does not light
upon transmission of supervision messages.
Alarm Period:
Approx. 3 seconds.
Rearm Timer:
Rearms the detector 2 minutes after the last alarm.
WIRELESS
Frequency:
2.4 Ghz as per IEEE 802.15.4
Tamper Alert:
Reported when a tamper event occurs and in any
subsequent message, until the tamper switch is restored.
Supervision Message:
Signaling at 24-minute intervals.
MOUNTING
Height:
1.8 - 2.4 m (6 - 8 ft). See Figures 2 – 6.
Installation Options:
See Figures 2 – 6.
ENVIRONMENTAL
Operating Temperature:
-10°C to 50°C (14°F to 122°F).
Storage Temperature:
-20°C to 60°C (-4°F to 140°F).
RFI Protection:
> 20 V/m to 1000 MHz.
Compliance with standards:
USA: CFR 47 part 15, Canada: RSS 210
.
ANSI/UL 639, ULC – S306
PHYSICAL
Dimensions (H x W x D):
105 x 35 x 30 mm (4-1/8 x 1-3/8 x
1-3/16 in.).
Weight (with battery):
60 g (2.1 oz).
Color:
White.
PATENTS
U.S. Patent 5,693,943 (other patents pending)
