Viscount Legend '70s Artist, Руководство пользователя

Страница: 11 / 146

EN - 9
Legend ‘70s – User Manual
Front panel
EFFECT section controls
This section includes the main controls of the effects. There are two available, independent effects. They have
the same set of controls but different values. When one of the two effects is selected, the control Leds of this
section are updated according to the settings of the currently selected effect.
The display shows several parameters to adjust the effect. For further information read the
Effects section (page
32 ).
Effect type selection knob.
Available effect types:
Effect Description
Tremolo Tremolo or vibrato effect. Rotate the [AMOUNT] knob to adjust the effect depth. Rotate the [RATE] knob
or press the [TAP] button to set the modulation speed.
Chorus Chorus effect. Rotate the [AMOUNT] knob to adjust the effect amount. Rotate the [RATE] knob or press
the [TAP] button to set the modulation speed.
Flanger Flanger effect. Rotate the [AMOUNT] knob to adjust the effect amount. Rotate the [RATE] knob or press
the [TAP] button to set the modulation speed.
Phaser Phaser effect. Rotate the [AMOUNT] knob to adjust the effect feedback. Rotate the [RATE] knob or
press the [TAP] button to set the modulation speed.
Wah Wah-wah effect. Rotate the [AMOUNT] knob to adjust the filter's resonance. The [RATE] and the [TAP]
button can adjust different parameters according to the currently selected Wah effect.
Amp Amplifier effect. Rotate the [AMOUNT] knob to adjust the distortion. Rotate the [RATE] knob to set the
output level of the effect. When the Rotary effect is selected, the [RATE] knob selects the rotation speed
(Slow-Fast) while the [TAP] button stops the rotation (Brake).
Delay Delay effect. Rotate the [AMOUNT] knob to adjust the effect amount. Rotate the [RATE] knob or press
the [TAP] button to set the time span between the repetitions of the signal.
Others
Various effects (equalizers, compressors, etc..). For further information read
the Effects section
(page 32 )
.
Effect selection buttons.
As described in the introduction to this section, there are two available effects. To select one and adjust its
parameters through the panel controls in this section, press the buttons [1] and [2]. When one of the two
effects is selected, the Led lights of this section
’s controls are updated according to the settings of the
currently selected effect. The blinking Led of button [1] or [2] indicates that though that effect is not
selected, it is still active.
[AMOUNT] knob.
Use this knob to adjust the effect intensity. For further information on the parameters that can be
controlled by this knob, read point 6 in this section or the
Effects section (page 32 ).
[TAP] button.
Press this button to set the tempo or modulation frequency manually. Tap the tempo on the button at least
four times to set the value manually. The [RATE] knob Led will blink at the speed calculated from your
tapping (see point 10). For further information on the parameters that can be controlled by this knob, read
point 6 in this section or the
Effects section (page 32 ).
[RATE] knob.
Set the modulation speed for the selected effect. The Led on this control blinks at the selected speed.
For further information on the parameters that can be controlled by this knob, read point 6 in this section or
the
Effects section (page 32 ).
6
NB
- Press this knob to select the effect type.
- Press the knob for a short while to access the effect parameters.
7
8
9
10
NB
- The light of the [RATE] knob is switched off when the effect is inactive, or when using specific effect types.
- When the Rotary effect is selected, the light blinks at either a slow or fast speed, depending on the currently
selected Rotary speed (Slow or Fast). The led does not blink when the Rotary is in Brake position.
-