background image

16

©

2002 

Directed Electronics, Inc.

To access another feature in the same menu:

1. Press and release the Valet/Program switch the number of times necessary to advance from the

feature you just programmed to the next one you want to program. 

2. Then press the Valet/Program switch once more and HOLD it. 

For example, if you just programmed the third feature in the menu and you would like to program

the seventh feature in the menu, you would press and release the Valet/Program switch four times

and then press it once more and HOLD it. The siren would chirp seven times to confirm access to

the seventh feature.

To select another menu:

1. Press and HOLD the Valet/Program switch.

2. After three seconds, the unit will advance to the next menu and the siren will chirp, indicating

which menu has been accessed. 

For instance, if you just programmed some features in Menu #1 (Basic Features) and you wish to

program a feature in Menu #2, you press and HOLD the Valet/Program button. After three

seconds, the siren chirps twice indicating access to Menu #2.

To exit the learn routine do one of the following:

Close the open door. 

Turn the ignition on.

No activity for longer than 15 seconds.

Press the Valet/Program switch too many times.

Содержание 650XV





























Отзывы: