background image

© 2000 Directed Electronics, Inc. Vista, CA

system features menus

Items in 

bold

text have been programmed to the two chirps setting at the factory.

FEATURE NUMBER

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

2-1

Siren

Horn honk

2-2

30-second siren duration

60-second siren duration

2-3

Nuisance Prevention Circuitry

ON

Nuisance Prevention Circuitry

OFF

2-4

Progressive door trigger

Instant door trigger

2-5

Valet switch input: 1 pulse

Valet switch input: 2-5 pulses

2-6

Door trigger error chirp ON

Door trigger error chirp OFF

2-7

Ignition-controlled domelight ON

Ignition-controlled domelight OFF

2-8

Single unlock pulse

Double unlock pulse

2-9

Channel 3: Validity

Channel 3: latched/latched, reset 
with ignition/30-second timed/
second unlock output

menu #2 - advanced features

FEATURE NUMBER

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

1-1

Active arming

Passive arming

1-2

Chirps on

Chirps off

1-3

Ignition-controlled door locks on

Ignition-controlled door locks off

1-4

Active locking only

Passive locking

1-5

Panic with ignition on

No panic with ignition on

1-6

0.8 second door lock pulses

3.5 second door lock pulses

1-7

Forced passive arming on

Forced passive arming off

1-8

Automatic engine disable on

Automatic engine disable off

1-9

Armed When Driving (AWD)

Vehicle Recovery System (VRS

®

)

1-10

Code Hopping

On

Code Hopping

off

menu #1 - basic features

Содержание 420ESP

















Отзывы: