background image

Functions

Configurable parameters

Monostable relay

• 

69PH identifier (see paragraph 4 “ID assignment”)

• 

Operating modes = “DEFAULT”

• 

Group 1 = 0 

• 

Group 2 = 0

• 

Group 3 = 0

• 

Group 4 = 0

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Call-activated monostable relay

• 

Operating modes = “Monost.Call Accept.”

• 

Enabling map = enable devices that send and receive the call (all enabled by default)

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Door lock command activated monos-

table relay

• 

Operating modes = “Monost. On SR”

• 

Enabling map = enable devices that send and receive the command (all enabled by default)

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Monostable relay activated by com-

mand F1

• 

Operating modes = “Monost. On F1”

• 

Enabling map = enable devices that send and receive the command (all enabled by default)

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Monostable relay activated by com-

mand F2

• 

Operating modes = “Monost. On F2”

• 

Enabling map = enable devices that send and receive the command (all enabled by default)

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Call attempt activated monostable relay • 

Operating modes = “Call Att.Enabl.Map”

• 

Enabling map = enable devices that send and receive the call (all enabled by default)

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Monostable relay activated by call at-

tempt to master unit

• 

Operating modes = “Call Att.to Group”

• 

Group 1 = ID indoor station 

• 

Group 2 = ID indoor station 

• 

Group 3 = ID indoor station

• 

Group 4 = ID indoor station

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Button-activated bistable relay

• 

69PH identifier (see paragraph 4 “ID assignment”)

• 

Operating modes = “Bistable”

• 

T1 activation delay time (def. 1s)

• 

T2 deactivation delay time (def. 1s)

• 

FLAG “State Not.” (YES = sends status with each switch, NO = does not send)

Bistable relay activated by accepted call. • 

Operating modes = “Bist.Accept.Call”

• 

Enabling map = enable devices that send and receive the command (all enabled by default)

• 

T1 activation delay time (def. 1s)

• 

T2 deactivation delay time (def. 1s)

• 

FLAG “Int.Call” (YES = Deactivates at end of call. NO = Deactivates on answering or, if external call, at end of electronic unit chime cycles)

Call repeater

• 

Operating modes = “Default”

• 

Group 1 RL1 = Group 1 RL2 = ID indoor station

• 

Group 2 RL1 = Group 2 RL2 = ID indoor station

• 

Group 3 RL1 = Group 3 RL2 = ID indoor station

• 

Group 4 RL1 = Group 4 RL2 = ID indoor station

• 

“Chime cycles” = desired number of cycles

Generic call repeater

• 

Operating modes = “Default”

• 

Group 1 RL1; 

 Kind of call repeated for Group 1 RL1

• 

Group 2 RL1; 

 Kind of call repeated for Group 2 RL1

• 

Group 3 RL1; 

 Kind of call repeated for Group 3 RL1

• 

Group 4 RL1; 

 Kind of call repeated for Group 4 RL1

• 

Group 1 RL2; 

 Kind of call repeated for Group 1 RL2

• 

Group 2 RL2; 

 Kind of call repeated for Group 2 RL2

• 

Group 3 RL2; 

 Kind of call repeated for Group 3 RL2

• 

Group 4 RL2; 

 Kind of call repeated for Group 4 RL2

• 

“Chime cycles” = desired number of cycles

N.B. For repetition of calls from 6120, the “landing group” flag of the called indoor station must be enabled.

Call repeater from 6120

• 

Operating modes = “Call Rep. 6120"

• 

Enabling map = enable devices that send and receive the call (all enabled by default)

• 

“Chime cycles” = desired number of cycles

Roller Shutter mode

• 

Operating modes = “Roller Shutter Mode”

• 

T1 delay time (def. 1s)

• 

T2 activation time (def. 1s)

Call progression

• 

Operating modes = “Call progression”

Table 6

7

EN

69PH

Содержание ELVOX 69PH



















Отзывы: