Viking K-1775-IP Series Скачать руководство пользователя страница 18

18

If enabled and a busy is detected, the 

K-1775-IP

phone will dial the “Roll Over” speed dial number. 

Notes:

This feature is enabled in the factory default setting. If the busy signal is interrupted with a promotional message,

contact your central office to have it removed.

38.  Dial Next Number on Busy 

39. Live Dialing Format

40. REX Input

The Live Dialing Format can be set to In-Band DTMF (Touch Tones) or RFC 2833 (Out of band DTMF Touch Tones).
Live dialing refers to the numbers dialed after and outbound call has been answered by the distant party. This would
typically be the numbers dialed to steer through automated attendants, voice mail, etc. If your VoIP phone system does
not automatically convert out of band DTMF to In-Band after the call is answered, set Live Dialing Format to “Inband
DTMF”

The 

K-1775-IP

has one Reguest for Exit (REX) trigger input. The REX switch must have a momentary, normally open-

contact. When the 

K-1775-IP

detects a contact closure on the REX trigger input and relay 2 mode is not set to Door

Strike, reay 1 will be energized for the preprogrammed relay activation time. If relay 2 is set to door strike then relay 2
will activate from the REX switch. This is useful in two door vestibule applications where relay 1 is used to unlock the
outside door and relay 2 to unlock the inside door.

Operation

A.  “CALL” Button

B.  Remote Access Operation Commands

The following commands can be entered after answering an inbound call from the entry phone. The commands can
also be entered on an outbound call to the entry phone. After the entry phone auto answers the call, two beeps will be
heard. If the access code has been disabled, you can now enter the Remote Access Operation Commands below. If an
Access code has been programmed, enter the Access code digits. With the correct code entered, two beeps will be
heard and you can now enter the Remote Access Operation Commands below.

With the call button Auto Dial Delay set to 0/Disable (factory default), when the “

CALL

” button is pressed, the 

K-1775-

IP

phone immediately dials the pre-programmed telephone number stored in the Phone Number Database Index location

0. With the call button Auto Dial Delay set from 1 - 6, when the “

CALL

” button is pressed you will hear 1 - 6 seconds of

dial tone, allowing you time to enter the 1-3 digit Speed Dial number. The unit will then dial the Phone Number Database
Index location 0-250 associated with the preprogrammed 1-3 digit Speed Dial Number (0-999). The Call Status LED
momentarily flashes during dialing. In the event the line is busy or there is a ring-no-answer, the unit can be programmed
to call a second roll over number.

When the call is answered, the phones are factory programmed to automatically light the “Call Status” LED to show    

that handsfree communication to personnel is established. Once the “Call Status” LED is on, relay activation commands
can be entered or the # key can be used to force the phone to hang-up.

After communication is established, enter the 1 or 2 digit relay activation command (factory set to “

QQ

for Relay 1 and

Q

2” for Relay 2

) to momentarily activate the entry phone (door strike) relay. If the (door strike) relay is activated, two

beeps    will be heard confirming the relay has been activated. If you require the relay to remain on continuously (ie: a
truck delivery), enter Touch Tones “

11 or 21

” to continuously activate that relay. A double beep will indicate the (door

strike) relay is latched on. When the visitor calls in again (ie: they are finished unloading the truck), enter Touch Tones

10 or 20

” to deactivate that relay. A single beep will indicate the (door strike) relay is latched off.

Содержание K-1775-IP Series























Отзывы: