14
5. Phone Name
6. Mute Alarm Until Next Failure
7. Phone Firmware
8. IP Firmware
9 Import/Export
Up to a 32 digit phone name can be assigned to the
K-1775-IP
being programmed. Often times the building name and
entrance location near the unit are used for the name.
A network failure alarm will be indicated by flashing the “Call” LED on the front panel and the speaker outputting 3 beeps
every minute. A network failure indicates the unit is not registered to the SIP server or there is a communication failure
with the gateway. The three beeps can be muted by clicking on the “Mute Alarm Until Next Failure”.
If new
K-1775-IP
firmware is available, after opening the programming software a pop window will come up asking you
if you would like to update firmware. An alternative method of updating can be done by clicking the phone firmware “Up-
date” button. You can then browse to the folder that contains the HEX file for updating the unit’s firmware. This method
is typically only used when Viking Technical Support has sent you updated firmware.
If new
K-1775-IP
firmware is available, after opening the programming software a pop window will come up asking you
if you would like to update firmware. An alternative method of updating can be done by clicking the IP firmware “Update”
button. You can then browse to the folder that contains the PIP file for updating the unit’s IP firmware. This method is
typically only used when Viking Technical Support has sent you updated IP firmware
The Import/Export feature is useful for backing up all the
K-1775-IP’s
programming or for importing programming when
installing multiple units with a majority of the same programming.
Clicking on the “Factory Default ” button in programming will reset all of the Programming Features back to their factory
default settings.
Note:
This command will not change or reset your IP settings.
10. Factory Default
The security code allows the user/installer to program the
K-1775-IP
phone. The factory set security code is 845464
(V-I-K-I-N-G). It is recommended that the factory set security code be changed.
Note:
The security code must be 6 digits and cannot include a
Q
or a
#
.
12. Security Code
11. Diagnostics
The Diagnostics section in the
K-1700-IP
PC Programming can be used to test the functionality of the MIC, Speaker
and Relays.
The Access Code is used for remotely operating the relays (Doorstrike, Mag-Lock, etc) by calling into the unit. This
code provides basic security and only allows operation of the relays and not the ability to change any of the programming
parameters. Once entered, any of the “Remote Access Operation Commands” can be used. The code can be 1 to 6
digits in length and cannot contain a “
Q
”, “#” or match the numbers used for the security code. Simply call the
K-1775-
IP
phone, the unit will automatically answer the line and output two beeps. You then enter the programmed 1 to 6 digit
access code, 2 beeps should be heard. You can now enter any “Remote Access Operation Commands” (see page 12).
13. Access Code
The Auto Answer/Loud Ring feature can be set to one of four modes.
0 = Disabled
: In the “Disabled” mode the phone will not automatically answer an incoming call.
1 = Auto Answer
(factory setting): In the “Auto Answer” mode the phone will automatically answer an incoming call on
the first ring.
2 = Loud Ring
: In the “Loud Ring” mode the phone will not automatically answer an incoming call but will output a loud
ring signal out of the speaker in a 2 seconds on, 4 seconds off ring pattern. The call can then be answered by pressing
the button.
3 = Loud Ring with AGC
: In the “Loud Ring with AGC” mode the phone will not automatically answer an incoming call
but will output a loud ring signal out of the speaker in a 2 seconds on, 4 seconds off ring pattern. The phone will auto-
matically increase or decrease the ring volume based on background ambient noise. The call can then be answered by
pressing the button.
14. Auto Answer / Loud Ring
