
63
DE
FR
NL
IT
ES
PT
NO
SV
FI
DA
PL
SL
EN
0478 201 9908 C - EN
* Warning
In the case of mains fuses of less than
16 A, these may be tripped during start-
up or in the case of high load operation
of the machine.
Fault:
Motor does not start
Possible cause:
– Motor overload protection activated
– No mains voltage
– Electric cable, plug, plug connector or
switch defective
– Fuse in UK plug damaged (only applies
to machines for UK)
– Feed chute ATO 400 not properly
closed – safety cut-off switch actuated
(safety interlock)
– Blade disc blocked
Remedy:
– Allow machine to cool down (
– Check power cable and fuse
– Check cable, plugs, connector and
switch and replace if necessary (by
electrician)
– Replace fuse
– Close feed chute ATO 400 properly and
fasten (tighten On- / Off switch) (
– Remove feed chute and remove
shredder deposits from the housing
(Important: disconnect the power cable)
(
Fault:
Reduced shredding performance
Possible cause:
– Blunt blades
– Incorrectly ground blades
– Power cable too long
– Bent blade disc
– GE 450: Incorrect rotational direction of
blade disc
Remedy:
– Reverse or sharpen blades
– Sharpen blades correctly
– Check blade disc visually
– GE 450: Change incorrect rotational
Fault:
Shredding material is not drawn in
Possible cause:
– GE 450: Incorrect rotational direction of
blade disc
– Blunt or incorrectly ground blades
– Gap between the two blades (hard
material blade disc)
– Blade cover not removed
Remedy:
– GE 450: Change incorrect rotational
direction of blade disc (
– Regrind blade and ensure sharpening
angle is exactly correct
– Install blades onto the hard material
20.
1
Handover confirmation
GE 450.
1
:
Motor, design
Electric motor
(3~)
Manufacturer
ATB
Type
BSRF 0.75/2-C
Voltage
400 V
Power input
3800 W
Fuse
10 A
In accordance with
Directive
2000/14/EC:
Guaranteed sound
power level L
WAd
108 dB(A)
In accordance with
Directive
2006/42/EC:
Sound pressure level
at workplace L
pA
95 dB(A)
Uncertainty K
pA
4 dB(A)
Maximum branch
diameter
55 mm
1
9. Troubleshooting
If necessary, contact a specialist
dealer; VIKING recommends VIKING
specialist dealers.
20. Service schedule
Содержание GE 420
