Viking G-5S Скачать руководство пользователя

Страница: 6 / 44

CONTROL BOARD REFERENCES:

1. HEAT SINK - SLAVE MODULE

secures the control board and dissipates heat.

2. SLAVE MODULE POWER HARNESS CONNECTOR

provides power to the Slave Module. pg 23

3. FUSE HOLDER - 15 AMP

for the Slave motor circuit.

4. “FAIL SAFE/SECURE” Jumper - SLAVE MODULE

power failure option. pg 26

5. M/S COMM CABLE CONNECTION - SLAVE MODULE

for master/slave (dual) gate application. pg 23

6. STATUS LEDs - SLAVE MODULE

provides diagnostic information.

7. SLAVE MOTOR CONNECTION

provides power to the Slave motor. pg 23

8. HEAT SINK - MASTER/SINGLE

secures the control board and dissipates heat.

9. FUSE HOLDER - 4 AMP

not applicable to this model.

10. FUSE HOLDER - 15 AMP

for the Master motor circuit.

11. LIMIT SETUP BUTTONS

available for future developments.

12. LCD DIAGNOSTICS DISPLAY

provides error messages, diagnostics settings

and operator status information. pg 36-38

13. M/S COMM CABLE CONNECTION - MASTER BOARD

for master/slave (dual) gate application. pg 23

14. “DIAGNOSE” LED

informs that errors have been detected and

available on LCD Display. pg 36-38

15. “DIAGNOSE” Button

allows you to navigate through the

Diagnostics LCD Display. pg 36-38

16. FEATURE ACTIVATION PIN HEADERS

activate features by placing a jumper onto the

pin headers. pg 26

17. “AUX. PWR” Terminal Block

used for solar applications & in-motion

warning devices. pg 21, 26

18. ON-BOARD 3 BUTTON STATION

controls the gate during set up.

19. “Siren” TERMINAL BLOCK

Vikings UL Siren is connected here. pg 12, 27

20. CONTROL BOARD MOUNTING HOLES

secures and grounds the control board.

21. POWER HARNESS CONNECTOR

provides power to the control board. pg 21

22. MASTER or SINGLE MOTOR CONNECTION

provides power to the motor. pg 22

23. “FAIL SAFE/SECURE” Jumper

power failure option. pg 26

24. FEATURE ACTIVATION TRIM POTS

activate and set features. pg 25

25. “EPS1” CONNECTOR

communication for Viking Solar Charger.

26. “EPS2” CONNECTOR

available for future developments.

27. “EMI”

CONNECTOR

not applicable to this model.

28. “CHECK MOTOR” Status LED

indicates motor power status. pg 34

29. “BATTERY LOW” Status LED

indicates battery power status. pg 34

30. “POWER” Status LED

control board power status. pg 34

31. “MAGNETIC LOCK Relay” Status LED

status of this on-board relay. pg 34

32. “MAGNETIC LOCK Relay” Terminal Block

connect electric locks here. pg 34

33. INPUT STATUS LEDs

indicates input status. pg 34-35

34. ACCESS CONTROL TERMINAL BLOCKS

accessory connections. pg 28-31, 40-42

www.PerformanceGateOpeners.com | (800) 878-7829 | [email protected]

Содержание G-5S













































Результаты поиска

Содержание G-5S

Отзывы:

Похожие инструкции для G-5S

Бренды по названию

Популярные бренды

Viking G-5S, Руководство по установке

Результаты поиска

Содержание G-5S

Отзывы:

Похожие инструкции для G-5S

Бренды по названию

Популярные бренды