manualshive.com logo in svg

Viking G-5S, Руководство по установке

Поделиться
Скачать
Viking G-5S Скачать руководство пользователя страница 36

3 4

LED References

In addition to the LCD Display, the control board LEDs monitor the various circuits of the 
control board. Use the table below to identify the corresponding “TS Ref#” and refer to 
pages 36-39 for further troubleshooting.

TROUBLESHOOTING

# LED

Status

Meaning

Page 39

TS Ref#(s)

1

“Magnetic  
Lock Relay”

OFF

At Closed Limit and Magnetic Lock Relay state is closed across “COM”  & 
“N.C.”.  Gate should be at the Close Limit.

SOLID

Not at Closed Limit and Magnetic Lock Relay state is closed across “COM”  & 
“N.O.”. Gate should not be at the Close Limit

2

“Check Motor” OFF

Normal Condition.

SOLID

The control board is sending power to the motor but the circuit is open.

7, 8

3

“Battery Low” OFF

Normal Condition.

SOLID

Does not apply to Solar Units.

FLASHING

Batteries critically low. Check power supply to the operator. (pg 21).

4

“POWER”

OFF

No power to control board (pg 21) or board is in sleep mode.

5

SOLID

Normal Condition.

5

“Radio”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the 
Radio terminal or when more than one device is connected  (pg 29, 40).

9, 10

6

“UL”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the UL 
terminal (pg 10-11, 28, 40).

9, 10, 16, 

22

7

“Re-Open”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the Re-
Open terminal or when more than one device is connected (pg 10-11, 28, 
31, 40).

9, 10, 16, 

22

8

“ATG”

OFF

Normal Condition.

SOLID

Control Board is receiving an input from a device connected to the ATG 
terminal (pg 30, 40).

9, 10

www.PerformanceGateOpeners.com  |  (800) 878-7829  |  [email protected]

Содержание G-5S













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды