Viking G-5S Скачать руководство пользователя | Manualshive

Страница: 19 / 44

background image

1 7

Limit Switch Setup

GATE OPERATOR INSTALLATION

STEP 1

Remove the Lead Screw Cover:

a. Remove the cover mounting screw.

b. Slide the cover off.

!

TIP:

Leave the cover off until after

the installation of the ECU Box and
electrical installation. Verify that the
operator opens and closes to the
desired limit positions under power.
Make any adjustments as necessary

STEP 2

Position the Limit Switches:

a. Loosen the setscrews on the Limit

Switch Holders and slide the Limit
Switches to the desired positions.

b. Move the gate manually and ensure the

Limit Switches are actuated (click) at
the desired open and closed positions.

c. Resecure the Limit Switch Holders

when the proper position has been
determined. DO NOT OVERTIGHTEN

STEP 3

Positive Stop Collar:

a. After the limit positions have been

verified, partially open the gate and
position the Positive Stop Collar as
shown, with a 1/16” gab between the
Collar and the Limit Switch Holder.

b. Tighten the Collar EVENLY to secure.
c. Run the gate two complete cycles and

check that the Lead Screw Carrier
makes firm contact to the Positive Stop
Collar.

STEP 4

Reinstalling the Lead Screw Cover:

a. Ensure that the End Cap is properly

positioned over the tip of the Lead
Screw as shown.

www.PerformanceGateOpeners.com | (800) 878-7829 | [email protected]

«
...
17
18
19
20
21
...
»

Содержание G-5S













































Отзывы:

Нет отзывов

Похожие инструкции для G-5S

Бренд: FAAC Страницы: 6

BOTTICELLI B CRC 480 D01

Бренд: BFT Страницы: 40

Бренд: Chamberlain Страницы: 80

Бренд: Chamberlain Страницы: 2

CAPTIVE CAP ACTIVE

Бренд: GiBiDi Страницы: 24

Бренд: Proteco Страницы: 10

Бренд: Wisniowski Страницы: 80

Бренд: Becker Страницы: 52

Бренд: CAME Страницы: 64

Бренд: Westinghouse Страницы: 10

Бренд: FlexiForce Страницы: 16

Бренд: Rival Страницы: 12

AccessMaster M100

Бренд: Chamberlain Страницы: 36

CCO-50NC Series

Бренд: CUISINEART Страницы: 6

Бренд: Beninca Страницы: 20

Бренд: Yolink Страницы: 29

Бренд: DACE Страницы: 12

Aviator II PREMIUM Series

Бренд: Raynor Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды