Viking G-5S Скачать руководство пользователя | Manualshive

Страница: 20 / 44

background image

1 8

ECU BOX INSTALLATION

Mounting Surface

Control Box

Sealed Washer

(Supplied with Unit)

Mounting Fastener

(Customer Supplied)

STEP 1

Disconnect the Siren,
Stop Button and EMI
Harness from the Control
Board. Remove the
Control Board Mounting
Plate. The plate is held in
the box by four screws.

STEP 2

Position the ECU Box
in the desired place
and mark the mounting
holes. Prepare the holes
to receive the anchors/
fasteners.

NOTE: Anchors are Not
Supplied.

STEP 3

Position the ECU Box
and secure it to the
mounting surface using
the Sealed Washers
provided (rubber side
of the washers against
the inside of the control
box).

Mounting the ECU Box

!

WARNING:

If the control box is not mounted properly it may fall, causing damage and/or

injury. The Electronic Control Unit (ECU) weight is approximately 40 lbs. Be sure that the
substrate being mounted to and the fasteners being used are appropriate to support the
weight of the control box.

www.PerformanceGateOpeners.com | (800) 878-7829 | [email protected]

«
...
18
19
20
21
22
...
»

Содержание G-5S













































Отзывы:

Нет отзывов

Похожие инструкции для G-5S

Бренд: Jaytech Страницы: 13

Бренд: Wayne-Dalton Страницы: 18

Бренд: Wayne-Dalton Страницы: 22

Бренд: V2 Страницы: 12

6400 - UL 325 Class 1

Бренд: DKS Страницы: 22

Бренд: 4Ddoors Страницы: 26

Бренд: CAME Страницы: 32

Бренд: Xtreme Garage Страницы: 28

Бренд: Xtreme Garage Страницы: 28

Бренд: RIB Страницы: 48

Бренд: CAME Страницы: 144

Бренд: RIB Страницы: 56

Бренд: tau Страницы: 44

Бренд: Hard Head Страницы: 33

S450 UK KIT-CBAC

Бренд: FAAC Страницы: 11

Бренд: FAAC Страницы: 4

Бренд: Wayne-Dalton Страницы: 26

TorqueMaster Plus 9800

Бренд: Wayne-Dalton Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды