9
Description
Enter Digits
Enable entry phone Caller ID (factory setting)
Q
1
Disable entry phone Caller ID
Q
2
Entry phone calls give custom double ring cadence (factory setting)
Q
3
Entry phone calls give standard ring cadence
Q
4
Dial “9” to access an outside line
Q
5
Instant outside line access (factory setting, for use with private dial tone)
Q
6
Enable door strike latching/toggle commands (factory setting)
Q
7
Disable door strike latching/toggle commands
Q
8
Enable entry phone identifier beeps (factory setting)
Q
9
Disable entry phone identifier beeps
Q
0
Ignore touch tones to program an entry phone
##1 - ##4
Reset all programming to factory default settings
###
Erase all keyless codes
##8
This six digit number can be used to access the programming mode. The security code has been factory set to
845464
(V-I-K-I-N-
G). It is recommended that you change the security code to a personal 6 digit number. To change the security code, access
programming (see
Programming
section
A
). Enter six digits 0-9 followed by
#47
. If you have forgotten your security code, follow
the steps in
Programming
section
A, 2. Accessing the Programming Mode Locally (Security Code Bypass Mode)
.
Note:
The
security code must be six digits in length and can NOT contain a
Q
or
#
.
C. Security Code (#47)
D. Dip Switch Programming
LED3
LED1
LED2
LED4
LED5
LED6
LED7
C
C
C
C
C
C
C
J11-
1
2
3
J10-
1
2
3
J9-
1
2
3
J8-
1
2
3
J7-
1
2
3
12
3
on
4
5
VIKING
©
MODEL C-2000B
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7
8 9 1 0 11 12 13
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PWR 13.8 V
A
C
EARTH GND
ENTR
Y
PHONE 1
DOOR STRIKE 1
ENTR
Y
PHONE 2
DOOR STRIKE 2
ENTR
Y
PHONE 3
DOOR STRIKE 3
ENTR
Y
PHONE 4
DOOR STRIKE 4
DOORBELL
SWITCH /
AUX. INPUT
AUX. CONT
ACT
OUTPUT
PHONE LINE
INPUT
LINE OUT
T
O
PHONES
ANALOG ST
A
TION
INPUT
DIP Switches shown
in the factory default
positions
OFF ON
12
3
on
4
5
14
Switch Position Description
1
OFF
Auxiliary Contact Mode
1
ON
Doorbell Mode (factory setting)
2
OFF
Normal Operation Mode (factory setting)
2
ON
Security Code Bypass Mode
3
OFF
Entry Phone automatic disconnect (CPC) disabled
Note:
Viking handsfree entry phones require CPC for
faster automatic disconnect.
3
ON
Entry Phone automatic disconnect (CPC) enabled
(factory setting)
4
OFF
Entry Phone busy signal disabled
4
ON
Entry Phone busy signal enabled (factory setting)
5
OFF
Single Line Ring Through Mode (factory setting)
5
ON
Analog Station Dial Through Mode
E. Privacy Number (#00)
F. Keyless Entry Codes and One Time Use Keyless Entry Codes
The “Privacy Number” is factory disabled so an entry phone off-hook will automatically ring the house phones. If
a “Privacy Number” is programmed, the visitor must touch tone dial the number to be able to call into the house.
The “Privacy Number” may be from 1 to 6 digits and is stored in location “
#00
”. To disable the “Privacy Number,”
clear the number’s memory location by entering “
#00
” without any previous digits.
Each entry phone may have a combination of up to 6 keyless entry codes or one time use keyless entry codes
for touch tone keyless entry. The keyless entry codes may be from 4 to 6 digits in length and are stored in locations
#11
-
#16
for entry phone 1,
#21 - #26
for entry phone 2,
#31 - #36
for entry phone 3, and
#41 - #46
for entry
phone 4. Up to 6 master keyless entry codes may be from 4 to 6 digits in length and are stored in locations
#51
- #56
. The master keyless entry codes can be used at any entry phone to activate that entry phone’s door strike.
To change any of the keyless entry codes to one time use, insert a
Q
in front of the specific memory location
during programming (ie: “
Q
#11
”). To clear any keyless entry codes, simply enter the location number (ie: “
#11
”
or “
Q
#11
”) without any previous digits.
G. Door Strike Activation Time (#19, #29, #39, #49)
A single pole double throw relay is available for each entry phone (a second set of contacts are available on solder
pads only), and each may be programmed with its own door strike activation time (programmed in seconds).
Each time must be 2 digits (Example: 00 = 1/2 sec) and is stored in locations
#19
,
#29
,
#39
and
#49
for relays 1
through 4 respectively. All activation times are factory set to 05 (5 sec)
Note:
A buzz sound will be heard in the
house phone and entry phone, indicating the door strike relay has been activated and visitors can now open the door.
