background image

TECHNICAL SUPPORT 1 800 908 0884

2

WARNING - Not following these instructions may cause severe injury or death to persons.

IMPORTANT SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To reduce the risk of severe injury or death:

1.

READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from the gate. 

NO ONE SHOULD CROSS THE PATH OF

THE MOVING GATE

.

4. Test the gate operator monthly. The gate 

MUST

reverse on contact with a rigid object or when

an object activates the non-contact sensors. After adjusting the force or the limit of travel,
retest the gate operator. Failure to adjust and retest the gate operator properly can increase the
risk of injury or death.

5. Use the manual release only when the gate is not moving.

6.

KEEP GATES PROPERLY MAINTAINED.

Read the owner’s manual. Have a qualified service per-

son make repairs to gate hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

8.

Every gate operator installation M

MU

US

ST

T have secondary protection devices

against entrapment, such as edge sensors and photo beams more in particularly
in places where the risk of entrapment is more likely to occur.

9.

SAVE THESE INSTRUCTIONS.

IMPORTANT INSTALLATION INSTRUCTIONS

1. Install the gate operator only when:

a) The operator is appropriate for the construction of the gate and the usage Class of the gate

(refer to page 5),

b) All openings of a horizontal slide gate are guarded or screened from the bottom of the gate

to a minimum of 4 feet (1.22 m) above the ground to prevent a 2-1/4 inch (57.2 mm) 
diameter sphere from passing through the openings anywhere in the gate, and in that 
portion of the adjacent fence that the gate covers in the open position,

c)

ALL EXPOSED PINCH POINTS ARE ELIMINATED OR GUARDED, AND

d)

GUARDING IS SUPPLIED FOR EXPOSED ROLLERS.

2. The operator is intended for installation only on gates used for vehicles. Pedestrians must be

supplied with a separate access opening. The pedestrian access opening shall be designed to
promote pedestrian usage. Locate the gate such that persons will not come in contact with the
vehicular gate during the entire path of travel of the vehicular gate.

3. The gate must be installed in a location so that enough clearance is supplied between the gate

and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging
gates shall not open into public access areas.

4. The gate must be properly installed and work freely in both directions prior to the installation

of the gate operator. Do not over-tighten the operator clutch or pressure 
relief valve to compensate for a damaged gate.

5. The gate operator controls must be placed so that the user has full view 

of the gate area when the gate is moving AND AWAY FROM THE GATE 
PATH PERIMETER,

Содержание Vehicular Gate Opener UL 325





































Отзывы: