manualshive.com logo in svg

Viessmann Vitocrossal 200 CM2C 115, Инструкция по эксплуатации, Страница: 9 / 64

Поделиться
Скачать
Viessmann Vitocrossal 200 CM2C 115 Скачать руководство пользователя страница 9

9

Record the volume filled, water hardness and pH value
on page 55.

Note

Observe the "Water quality requirements" on
page 53.

Filling the trap with water

Fig. 1

1. 

Fill the trap with water. To do this, pour water into
the boiler via the combustion chamber or the
inspection port of the flue system.

Danger

If the trap is not full, flue gas can escape.
Escaping flue gas can cause life threatening
carbon monoxide poisoning.
Always fill the trap with water 

before

 com-

missioning.

2. 

Check that the condensate can drain freely from
the condensate drain hose. Check the trap for
leaks.

3. 

If trap is leaking, unscrew the lower part. Check the
gasket and replace if necessary.

Commissioning the system

Danger

CO build-up as a result of incorrect burner
adjustment or flue gas system leakage can have
serious health implications.
Always carry out a CO test before and after
work on gas appliances.

■

Vitotronic operating instructions and service
instructions

■

Neutralising system operating instructions

■

Flue system installation instructions

Commissioning, inspection, maintenance

Filling the heating system with water and venting

5831036

 

Содержание Vitocrossal 200 CM2C 115

































































Отзывы:

Нет отзывов