manualshive.com logo in svg

Viessmann Vitocrossal 200 CM2C 115, Инструкция по эксплуатации, Страница: 13 / 64

Поделиться
Скачать
Viessmann Vitocrossal 200 CM2C 115 Скачать руководство пользователя страница 13

13

F

A

BCD

E

G

Fig. 4

0

1. 

Close the gas shut-off valve.

0

2. 

Switch off ON/OFF switch at the user interface of
the control unit.

0

3. 

Switch OFF the mains isolator (outside the instal-
lation room) or isolate the mains power and
secure against unintentional reconnection.

0

4. 

Undo fitting 

A

 from the gas supply pipe.

0

5. 

Disconnect control cable 

G

 from the gas train.

0

6. 

Release the gas train from flange 

E

.

0

7. 

Remove restrictor 

C

 with rubber cork gasket 

D

.

0

8. 

Insert O-ring 

B

, restrictor for LPG 

C

 and rubber

cork gasket 

D

.

Note

■

The bevel and label on the LPG restrictor must
point towards the gas train.

■

For gas restrictor allocation (hole diameter), see
specification.

0

9. 

Tighten M 5 nuts diagonally.
Torque: 1.5 Nm.

10. 

Secure fitting 

A

 with a new gasket.

11. 

Plug control cable 

G

 into the gas train.

12. 

Check control cables:

■

Connection and kink-free routing

■

Application and seating of retaining clips

13. 

Affix the label "Set to ..." 

F

 supplied over existing

label.

14. 

Start the burner.

15. 

Check for gas tightness.

Danger

Escaping gas leads to a risk of explosion.
Check gas routing components for leaks.

!

Please note

The use of leak detection spray can result in
faulty operation.
Leak detection spray must not come into
contact with electrical contacts.

16. 

Change gas type on the burner control unit. See
the following chapter.

17. 

Set gas pressure switch to 20 mbar (2 kPa).

Changing gas type on the burner control unit

Service instructions of the control unit

Status Service

S

R

Fig. 5

1. 

Press 

S

 and hold for longer than 2 s. 

" "

 flashes.

2. 

Press   until the display shows "6" under Service.

3. 

Press 

S

 until the display shows "6" under Status.

4. 

Press   until display shows "2" under Status and
the current gas type is shown under Service (0 =
natural gas or 1 = LPG).

5. 

Use   or   to select "1" for LPG.

6. 

Press 

S

 to confirm. If applied successfully, "1" will

be shown briefly on the display under Service, or
"0" will appear if it failed.

7. 

Press 

S

 to switch to the operating display.

8. 

Press 

R

.

The system will be restarted.

Commissioning, inspection, maintenance

Conversion to LPG P

 (cont.)

5831036

 

Содержание Vitocrossal 200 CM2C 115

































































Отзывы:

Нет отзывов