Viessmann Flue gas system Скачать руководство пользователя страница 3

Страница: 3 / 36

General installation instructions

Engineering

Prior to the installation check that the

maximum possible flue length in

accordance with the technical guide for

the respective boiler will not be exceeded.

Flue gas temperature protection

The flues are approved for flue gas

temperatures up to 120°C

Measures inside the Viessmann condensing

boilers ensure that the maximum

permissible flue gas temperature will never

be exceeded.

Installation information

The component overviews for the types

of routing also apply to the Vitocrossal

300 and the Vitoladens 300-T.

Keep flue paths as short as possible with

the fewest number of bends possible.

Check the gaskets in all female

connections.

Use only the special gaskets supplied

with the boiler.

Required tools/equipment

Rope for lowering the flue gas system

into a duct (length: chimney height plus 3

metres).

Saw and file for trimming and chamfering

the pipe sections.

Power drill for securing the duct cover and

the support rail.

Plug-in fem. connections in the flue must

always point in the flow direction.

Only use the components supplied with

the PP flue gas system.

Twist the pipes slightly whilst pushing

them in.

Inner and outer pipe can be trimmed to

the same length.

5458 035 GB

Содержание Flue gas system





































Результаты поиска

Содержание Flue gas system

Отзывы:

Похожие инструкции для Flue gas system

Бренды по названию

Популярные бренды

Viessmann Flue gas system, Руководство по установке

Результаты поиска

Содержание Flue gas system

Отзывы:

Похожие инструкции для Flue gas system

Бренды по названию

Популярные бренды