Viessmann Flue gas system Скачать руководство пользователя страница 7

Страница: 7 / 36

Installation requirements

Statutory requirements

The appliance is suitable only for installation in GB and IE and should be installed in accordance

with the rules in force. In GB a Gas Safe Registered Installer must carry out the installation. It

must be carried out in accordance with the relevant requirements of the:

Gas safety (installation and use) regulations (current issue)

It is in your own interest and safety to ensure that the law is complied with.

In addition to the above regulations, this

appliance must be installed in accordance

with the current IEE Wiring Regulations

for electrical installation (BS 7671), local

Building Regulations, the Building Standards

(Scotland) (Consolidation) Regulations, bye

laws of the local water undertaking and

Health and Safety Document NO. 635 ‘The

Electricity at Work regulations 1989’

In Ireland (IE), the installation must be

carried out by a Competent Person

and installed in accordance with the

current edition if I.S.813 “Domestic

Gas Installations”, The current Building

Regulations and references should be

made to the current ETCI rules for electrical

installation.

It should also be in accordance with the

relevant recommendations in the current

editions of the following British Standards

and Codes of Practice: BS 5449, BS 5546,

BS 5440:1, BS 5440:2, BS 6798, BS 7593,

BS 6891, IGE/UP/7 and IS 813 for IE.

All Registered installers are required to

notify building control when they have

installed or exchanged a gas appliance in

a residential dwelling, this can be done via

Gas Safe.

Gas Safe will then issue either a Building

Compliance Certificate (for England and

Wales) or a Declaration of Safety (Scotland,

Northern Island, Isle of Man or appliances

out of the scope of Building Regulations)

to the homeowner, which will confirm

that the work has been carried out by a

competent Gas Safe Registered Installer.

This document will be used to form part of

the Home Information Pack (HIP).

Please note

Manufacturers instructions must not

be taken in any way as overriding

statutory obligations.

Boiler Position

The following limitations must be observed

when siting the boiler:

The boiler is not suitable for external

installation. The position selected for the

installation should be within the building,

unless otherwise protected by a suitable

enclosure and must allow adequate space

for installation, servicing and operation

of the appliance and for air circulation

around it.

The position must allow for a suitable flue

system and terminal position. The boiler

must be installed on a flat vertical wall

capable of supporting the weight of the

appliance and any ancillary equipment

when full.

Due consideration should be given to the

routing of the condensate drain from the

chosen position.

If the boiler is to be fitted in a timber

framed building it should be fitted in

accordance with ige/up/7. If in doubt

advice must be sought from the Institute

of Gas Engineers.

5458 035 GB 08/20

Содержание Flue gas system





































Результаты поиска

Содержание Flue gas system

Отзывы:

Похожие инструкции для Flue gas system

Бренды по названию

Популярные бренды

Viessmann Flue gas system, Руководство по установке

Результаты поиска

Содержание Flue gas system

Отзывы:

Похожие инструкции для Flue gas system

Бренды по названию

Популярные бренды