Victaulic VE26 Series Скачать руководство пользователя страница 8

Страница: 8 / 44

TOOL NOMENCLATURE

NOTICE

• Drawings and/or pictures in this manual may be exaggerated for clarity.
• The tool, along with this operating and maintenance instructions manual, contains

trademarks, copyrights, and/or patented features that are the exclusive property of
Victaulic.

Hand

Crank

Inner Roll

Grooving Roll

Roll Arm

Tool Body

Depth Stop

Collars

Nose

Feed Screw

Feed Nut

Trunnion

Groove

Depth Stop

Gauges

Pipe-End

Stop (2)

Inner Grooving

Roll Shaft

Drive Nut

KEEP

HANDS

AWAY

Warning Label (Varies depending upon

which tool configuration is ordered)

Groove Diameter “C” Dimension

Label (Varies depending upon which

tool configuration is ordered)

OPPOSITE SIDE OF TOOL

TM-VE26_8

REV_C

TM-VE26

/ Operating and Maintenance Instructions Manual

Содержание VE26 Series













































Результаты поиска

Содержание VE26 Series

Отзывы:

Похожие инструкции для VE26 Series

Бренды по названию

Популярные бренды

Victaulic VE26 Series, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание VE26 Series

Отзывы:

Похожие инструкции для VE26 Series

Бренды по названию

Популярные бренды