background image

24

TROUBLE

SHOOTING

Problem

Possible cause

Remedy

Insufficient power (cont)

Improper fuel mixing ratio

Replace with correct 25:1 fuel mix

Machine is overworked

Operate properly – do not overload

Fan cover, cylinder fins, etc. dirty

Clean and remove dirt and debris

Engine makes knocking noise

Cylinder overheating 

Clean fins

Use of incorrect fuel

Replace with correct fuel

Poor acceleration

Fuel filter clogged

Contact Service Centre or replace

Fuel system clogged

Excessively low idle

Speed up idle/Contact Service 
Centre

Excessively lean carburettor setting 

Contact Service Centre

Clogged air filter

Clean filter

Air leakage

Loose carburettor

Contact Service Centre

Loose fuel pick up tube

Insert firmly/Contact Service Centre

Engine stops during operation

Stop switch is set to off position

Ensure stop switch is set to on

Engine stops abruptly

Shorting of spark plug

Clean spark plug or replace

Piston scored, ignition failure

Contact Service Centre

Miscellaneous

Fuel tank empty

Refuel

Carburettor or fuel tank clogged

Impeller clogged

Contact Service Centre

Remove blockage

Engine is difficult to shut off

Overheated engine

Run at idle before switching off

Overheating or electrical fault

Overheated spark plug

Clean & adjust gap  0.6 - 0.7mm 

Defective stop switch

Contact Service Centre or replace

Poor contact of ground wire

Contact Service Centre

Unit main body

Loose impeller

Contact Service Centre

Irregular vibration 

Bent main shaft

Worn shaft bearings 

Contact Service Centre

Contact Service Centre

Damaged impeller

Loose engine mounts

Contact Service Centre

Retighten engine mount screws

Can not assemble blower air tube 
or vac tube to main body

Screw still in main body

Debris on main body and/or blower 
air/vac tube

Refer to assembly procedures 

Clean blower main body and 
blower air/vac tube

Vacuum bag, fan & tubes

Unit will not blow or vacuum

Tube or bag is blocked

Fan is blocked

Vac bag is dirty

Vac bag is torn or punctured

Clear the blockage following the 
procedure in the manual.

Clear the blockage following the 
procedure in the manual.

Clean the Vac bag.

Replace the Vac bag.

  

Troubleshooting

If running difficulties continue, contact your closest Authorised Service Centre.

LR02390A-A.indd   25

22/07/2014   4:37:51 PM

Not for  

Reproduction

Содержание VPLV0226

































Отзывы: