VIA Technologies ART-5450 Скачать руководство пользователя

Страница: 70 / 103

Typematic Rate (Chars/Sec)

This item sets the rate (characters/second) at which the system
retrieves a signal from a depressed key.
Settings: [6, 8, 10, 12, 15, 20, 24, 30]

Typematic Delay (Msec)

This item sets the delay between, when the key was first pressed
and when the system begins to repeat the signal from the
depressed key.
Settings: [250, 500, 750, 1000]

Security Option

Selects whether the password is required every time the System
boots, or only when you enter Setup.

Settings

Description

Setup

Password prompt appears only when end users try to
run BIOS Setup

System

Password prompt appears every time when the
computer is powered on and when end users try to run
BIOS Setup

MPS Version Control for OS

Settings: [1.1, 1.4]

OS Select for DRAM > 64 MB

Settings: [Non-OS2, OS2]

HDD S.M.A.R.T Capability

Settings: [Disabled, Enabled]

Video BIOS Shadow

Settings: [Disabled, Enabled]

Full Screen Logo Show

Show full screen logo during BIOS boot up process.
Settings: [Disabled, Enabled]

Содержание ART-5450








































































































Результаты поиска

Содержание ART-5450

Отзывы:

Похожие инструкции для ART-5450

Бренды по названию

Популярные бренды

VIA Technologies ART-5450, Руководство пользователя

Результаты поиска

Содержание ART-5450

Отзывы:

Похожие инструкции для ART-5450

Бренды по названию

Популярные бренды