VIA Technologies ART-5450 Скачать руководство пользователя страница 69

Страница: 69 / 103

Quick Power On Self-Test

Shortens Power On Self-Test (POST) cycle to enable shorter boot
up time.

Settings

Description

Disabled

Standard Power On Self Test (POST)

Enabled

Shorten Power On Self Test (POST) cycle and boot up time

First/Second/Third Boot Device

Set the boot device sequence as BIOS attempts to load the disk
operating system.

Settings

Description

LS120

Boot from LS120

Hard Disk

Boot from the HDD

CDROM

Boot from CDROM

ZIP100

Boot from ZIP100

USB-FDD

Boot from USB Floppy

USB-ZIP

Boot from USB ZIP drive

USB-CDROM

Boot from USB CDROM

Legacy LAN

Boot from network drive

Disabled

Disable the boot device sequence

Boot Other Device

Enables the system to boot from alternate devices if the system fails
to boot from the “First/Second/Third Boot Device” lists.

Settings

Description

Disabled

No alternate boot device allowed

Enabled

Enable alternate boot device

Boot Up NumLock Status

Set the NumLock status when the system is powered on.

Settings

Description

Off

Forces keypad to behave as arrow keys

Forces keypad to behave as 10-key

Typematic Rate Setting

Enable “Typematic Rate” function.
Settings: [Disabled, Enabled]

Содержание ART-5450








































































































Результаты поиска

Содержание ART-5450

Отзывы:

Похожие инструкции для ART-5450

Бренды по названию

Популярные бренды

VIA Technologies ART-5450, Руководство пользователя

Результаты поиска

Содержание ART-5450

Отзывы:

Похожие инструкции для ART-5450

Бренды по названию

Популярные бренды