background image

4

3.6  BLANK VINYL

x

  Please make sure that the vinyl is perfectly flat when placed on the VRX-2000 for the vinyl cutting

procedure.  Vinyl that is not perfectly flat will prevent perfect quality recording.

x

 

If a bent or warped vinyl is used, the depth or width of the groove will be inconsistent.  It will cause a
distortion or needle skipping on playback.

x

 

On recording, please make sure the surface of the vinyl is clean.  Please do not use thinner or methylated
spirits for cleaning.

x

 

Before recording, please remove the protective sheets on both sides of the blank vinyl.  If the sheet is left
on the other side, the vinyl will not be properly secured on the silicone platter mat, which is essential for the
cutting process.

x

 

The special vinyl for the VRX-2000 has a similar durability of commercial vinyl, but a record cut in improper
circumstances/condition may have less durability than usual.

Section 4:   USER REGISTRATION & CUSTOMER SUPPORT

4.1 USER REGISTRATION CARD

x

 

The official Vestax user registration card is enclosed in the box.  Please fill out the card in full and send it to
Vestax customer support in (or nearest to) your country.  Vestax will not be able to service or support the
unit if it is not registered.  If you have any registration detail changes, please inform your customer service
center immediately.

x

 

Please contact customer support center with any questions regarding usage or operation.  Please fill out the
Investigation Form (found at the back of this manual) and submit to the service center by fax or mail.  The
service center will reply to all questions by fax or mail. Please note: some more detailed questions may take
a longer time to respond to.

x

 

Please see the final page of this manual to find relevant fax numbers and mailing addresses of Vestax
customer service centers.

Section 5:   WARRANTY REPAIR AND AFTER-SERVICE

x

 

Warranty Card: Please keep the warranty card and make sure that it has the date of purchase and store of
purchase.

x

 

Terms and Conditions of Warranty:  The VRX-2000 is covered by warranty for 12 months.  However, Vestax
will not honor warranty service if the unit is improperly used, physically damaged, modified by unauthorized
person or damaged by external equipment.  The cutting stylus is not covered by warranty.

Содержание VRX-2000

















Отзывы: