background image

not available. In this case its MMSI number will be displayed instead 
of the name and will look like 

<735023456>

. Since voyage 

information is received at a different interval than navigation 
information it may take several minutes to appear. 
A target may specify its navigation status and if available it is 
displayed as “Motoring”, “Sailing”, “Anchored”, “Moored”, etc. 

The navigation status may not be accurate. 

An important piece of information indicates when data was last 
received from a target. This is shown at the bottom of the target 
details screen. Although bearing, range, CPA, and TCPA are 
constantly updated by the 

AIS

WatchMate

 

as your vessel moves, you 

should consider the “age” of the information received from the target 
in determining how accurate the displayed data may be and to assist 
you in refining your assessment of collision risk.

PACIFIC PEARL

BRG

275

M

RNG

4.46nm

CPA

0.09

nm

TCPA

18:45

COG

310

T

SOG

12.4

K

HDG

315

T

ROT

R 5

°

 

/min

IMO

3923781

MMSI

270128210

CALL

ZL3AB

CLASS

A

ETA 

12/28 04:30

DEST

PAPEETE TAHITI

105m Tanker (Hazard: C)

4.6m Draft, 18m Beam

Restricted maneuverability
S 08

°

 50.068

W 140

°

 15.014

Mute

Home

Received 00:07 ago

If the target and your vessel will not converge, such as when they are 
moving away from each other, the CPA is shown as 

None 

and 

- 37 -

Содержание WatchMate 650




































































Отзывы: