vesper marine WatchMate 650 Скачать руководство пользователя | Manualshive

Страница: 24 / 67

background image

Gray

Serial port 1 data out.

If you are connecting this port

to a computer, connect this wire to pin 2 on a female
DB9 connector. If you are connecting this port to a
transponder, chart plotter or other device, connect this
wire to the data input for your device. If your device
has NMEA+ or NMEA A inputs then use that wire.

Yellow

Serial port 2 ground.

Connect this wire in the same

manner as serial port 1 ground, described above.

Green

Serial port 2 data in.

Connect this wire in the same

manner as serial port 1 data in, described above.

White

Serial port 2 data out.

Connect this wire in the same

manner as serial port 1 data out, described above.

Orange

External alarm relay contact 1.

Whenever the alarm

is sounding, an internal relay switches two external
alarm connections together. These connections are
normally open (NO) and will be closed whenever the
internal alarm is sounding. You may use these
connections to light an indicator or provide an external
buzzer or alarm. The maximum switched current is 2
amps. Do not exceed this value or damage may occur
to the

AIS

WatchMate

and void your warranty

.

It is

recommended that you include a suitable fuse (max
2A) to protect against overload. If you wish to connect
a device which requires more than 2 amps then you
must use an external relay which should be purchased
separately. It is recommended to consult a qualified
marine electronics technician if you require assistance
setting up an external alarm.

Black

External alarm relay contact 2.

See above.

- 24 -

«
...
22
23
24
25
26
...
»

Содержание WatchMate 650




































































Отзывы:

Нет отзывов

Похожие инструкции для WatchMate 650

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: Baileigh Industrial Страницы: 40

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Abicor Binzel Страницы: 92

Бренд: Mandam Страницы: 9

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды