![VERTO 52G530 Скачать руководство пользователя страница 11](http://html1.mh-extra.com/html/verto/52g530/52g530_instruction-manual_1008342011.webp)
11
Explanation of used symbols
1 2 3 4
5 6
7 8
9 10 11
IPX4
1.
Read the operator’s manual
2.
Keep away from bystanders
3.
WARNING – pay attention to sharp blades, keep away from
fingers and toes. Pull the plug out of the mains socket before
maintenance, adjustments, cleaning or in case of tangled or
damaged power cord. Blade keep rotating after the motor has
been switched off.
4.
Keep flexible power cord away from the blades.
5.
Protection level IPX4
6.
Electric shock protection class II.
7.
Use personal protection equipment (protective goggles, earmuff
protectors)
8.
Use protective clothes.
9.
Keep the tool away from children.
10. Protect the tool from moisture.
11. Recycling
CONSTRUCTION AND USE
Aerator / Verticutter is a device with insulation class II. It is driven
by single-phase AC commutator motor. The device is used for lawn
maintenance. Verticutter is equipped with blades that cut thatch
layer vertically and scarify the substrate. Then the soil is loosened and
aerated, water can reach the roots, so the grass grows and propagates
much better. The verticutter also destroys moss and other weed (annual
plants mainly, with shallow roots) that take light and nutritients from
the grass. Lawn verticutting is the process when the blades of the
machine cut the upmost layer of the lawn. You can fill produced holes
with appropriate turf-based substrate.
Aerator drives air into lawn by puncturing soil with special rods or spi-
kes. The process of aeration „perforates” the substrate and the produced
holes allow air to reach deeper layers. The device is intended only for
light duty tasks.
Use the power tool according to the manufacturer’s instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1.
Motor casing
2.
Outlet lid
3.
Handle bottom part
4.
Handle
5.
Safety button of the switch
6.
Switch lever
7.
Power supply socket
8.
Butterfly nuts of the joint
9.
Power cord holder
10.
Container
11.
Front ground wheel
12.
Aeration/verticutting depth adjustment lever
13.
Casing
14.
Container frame
15.
Container bag
16.
Reel fixing screw
17.
Reel
18.
Reel clamp
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1.
Handle bottom part
- 2 pcs
2.
Bolts + butterfly nuts
- 2 sets
3.
Screws
- 2 pcs
4.
Power cord holder
- 1 pce
5.
Clip for power cord holding
- 2 pcs
6.
Container frame
- 1 set
7.
Container bag
- 1 pce
8.
Aerator reel
- 1 pce
PREPARATION FOR OPERATION
INSTALLATION OF HANDLE
•
Put the handle bottom parts (
3
) in the aerator body (
13
) (
fig. A
).
•
Fix the handle bottom parts (
3
) with the supplied screws (
fig. B
).
•
Attach the power cord holder (
9
) to the handle (
4
).
•
Use bolts and butterfly nuts (
8
) to join the handle bottom parts (
3
) and
the handle (
4
) (
fig. C
).
•
Use supplied clips to fix the motor power cord to the handle (
fig. D
).
The handle should be installed so the switch lever is located on the
right side.
CONTAINER ASSEMBLY
•
Insert two rods of the frame (
14
) into sleeves to join them.
•
Put the container bag (
15
) over the container frame (
14
) (
fig. E
).
•
Attach plastic bag strips (
15
) to the container frame (
14
) (
fig. F
).
CONTAINER INSTALLATION
•
Lift the outlet lid (
2
) and attach the container (
10
) to the outlet. Use
two latches (
a
) in the upper part of the aerator body (
13
) (
fig. G
).
•
Lower the outlet lid (
2
).
The container is held in correct position with the spring of the outlet
lid (
2
). The container features comfortable handle to carry and empty
of grass cuts.
Always make sure the container is correctly fixed.
SETTING DEPTH OF AERATION / VERTICUTTING
Switch off the device and remove power cord plug from mains
socket before setting the aeration/verticutting depth.
Depending on the aeration/verticutting depth, the front ground whe-
els (
11
) can be set up in four different positions with the lever (
12
).
•
Pull the aeration/verticutting depth adjustment lever (
12
).
Содержание 52G530
