manualshive.com logo in svg

VersaLogic VL-12CT96, Справочное руководство

Поделиться
Скачать
VersaLogic VL-12CT96 Скачать руководство пользователя страница 37

VL-12CT96/7 Analog & Digital I/O Card

4-5

Convert Register

CONVERT — 0302H

7

6

5

4

3

2

1

0

D

7

D

6

D

5

D

4

D

3

D

2

D

1

D

0

Figure 4-7.  Convert Register

The CONVERT register is a write register which, when written to, triggers (starts) an A/D conversion.
It is data insensitive; any value written to the CONVERT register will produce a trigger.

There are two ways to trigger an A/D conversion:  writing to the CONVERT register or reading the
ADCHI register (if auto-trigger is enabled).

A word-wide output instruction to the SELECT register (out dx,ax) also writes into the CONVERT
register causing channel addressing and triggering with one CPU instruction.

D7-D0 — Not Used.  

These bits have no function on the VL-12CT96/7.  Any value written triggers an A/

D conversion.

Clear Flags Register

CLRFLG — 0309H

7

6

5

4

3

2

1

0

D

7

D

6

D

5

D

4

D

3

D

2

D

1

D

0

Figure 4-8.  Clear Flags Register

The CLRFLG register is a write register which, when written to, clears the Done bit in the STATUS
register.  It is data insensitive; any value written to the CLRFLG register will clear Done.

D7-D0 — Not Used.  

These bits have no function on the VL-12CT96/7.  Any value written will cause the

Done bit in the STATUS register to be cleared.

Registers — Analog Input Registers

Содержание VL-12CT96








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды