VersaLogic EPM-CPU-10 Скачать руководство пользователя страница 52

Страница: 52 / 55

Revision Indicator Register

Revision Indicator Register

REVIND (READ ONLY) 00E1h (or 01E1h via CMOS Setup)

D7 D6 D5 D4 D3 D2 D1 D0

PC4 PC3 PC2 PC1 PC0 TCO REV1

REV0

This register is used to indicate the revision level of the

EPM-CPU-10

product.

Bit Mnemonic Description

D7-D3 PC4-PC0 Product Code — These bits are hard coded to represent the product type. The

EPM-CPU-10 will always read as 00010. Other codes are reserved for future
products.

PC4 PC3 PC2 PC1 PC0

Product

Code

0 0 0 1 0

EPM-CPU-10

Note! This bits are read-only.

D2 TCO

Throttling Code — This bit specifies how throttling is enabled at power-up and
reset.

0 = EPM-CPU-10c No Throttling
EPM-CPU-10d

1 = EPM-CPU-10b Throttling set at 37.5%
EPM-CPU-10e

Note! This bit is read-only.

D1-D0 REV1-REV0 Revision Level — These bits are representative of the EPM-CPU-10 circuit

revision level.

REV1 REV0 Revision Level

Rev 3 or earlier

Rev 3.01 or later

1 0 Reserved

1 1 Reserved

Note! This bits are read-only.

42 – Reference

EPM-CPU-10 Reference Manual

Содержание EPM-CPU-10
























































Результаты поиска

Содержание EPM-CPU-10

Отзывы:

VersaLogic EPM-CPU-10, Справочное руководство, Страница: 52 / 55

Результаты поиска

Содержание EPM-CPU-10

Отзывы: