VersaLogic EPM-CPU-10 Скачать руководство пользователя страница 40

Страница: 40 / 55

Push-Button Reset

XTERNAL

PEAKER

A miniature 8 ohm speaker can be connected between JS4[29A] and JS4[30A].

This connector is protected with IEC 61000-4-2 (Level 4) rated TVS components to help protect
against ESD damage.

Push-Button Reset

A normally open, momentary action push-button reset switch can be connected between
JS4[19B] and JS4[20B]. Shorting JS4[19B] to ground will cause the

EPM-CPU-10

to reboot.

This connector is protected with IEC 61000-4-2 (Level 4) rated TVS components to help protect
against ESD damage.

Floppy Drive Interface

The

EPM-CPU-10

supports a standard 34-pin PC/AT style floppy disk interface via connector

JS3[JK] and JS3[JL]. Up to two floppy drives can be attached. CMOS Setup can be used to
enable or disable the floppy disk interface.

Note

The floppy drive used to boot the system (Drive A) should be connected after the
twist in the cable, JS3[JK].

Warning!

Cable length must be 18" or less to maintain proper signal integrity. The grounds in
this connector should not be used to carry motor current.

Table 12: Floppy Disk Interface Connector Pinout

JS3

Pin

Signal
Name

Function

JK/JL

Pin

Ground

2B R/LC

Load

Head

3B Ground Ground

4B NC

Connection

5B Ground Ground

6B NC

Connection

7B Ground Ground

8B INDX*

Beginning Of Track

9B Ground Ground

10B MTR1*

Motor

Enable

11B Ground Ground

12B

DRV0*

Drive Select 0

13B Ground Ground

14B

DRE1*

Drive Select 1

15B Ground Ground

16B MTR0*

Motor

Enable

17B Ground Ground

18B DIR

Direction

Select 18

19B Ground Ground

20B STEP*

Motor

Step

21B Ground Ground

22B

WDAT*

Write Data Strobe

23B Ground Ground

24B WGAT* Write

Enable

25B Ground Ground

26B TRK0*

Track

Indicator 26

27B Ground Ground

28B WPRT* Write

Protect

29B Ground Ground

30B RDAT*

Read

Data

31B Ground Ground

32B HDSL

Head

Select

33B Ground Ground

34B

DCHG

Drive Door Open 34

30 – Reference

EPM-CPU-10 Reference Manual

Содержание EPM-CPU-10
























































Результаты поиска

Содержание EPM-CPU-10

Отзывы:

VersaLogic EPM-CPU-10, Справочное руководство, Страница: 40 / 55

Результаты поиска

Содержание EPM-CPU-10

Отзывы: