background image

VFI33 Vent Free Gas Fireplace System

20307670

3

13. Avoid any drafts that alter burner fl ame patterns. Do not 

allow fans to blow directly into fi replace. Do not place 
a blower inside burn area of fi rebox. Ceiling fans may 
create drafts that alter burner fl ame patterns. Sooting 
and improper burning will occur.

14. 

CAUTION

: Candles, incense, oil lamps, etc. produce 

combustion byproducts including soot. Vent-free 
appliances will not fi lter or clean soot produced by 
these types of products. In addition, the smoke and/or 
aromatics (scents) may be reburned in the vent-free 
appliance which can produce odors. It is recommended 
to minimize the use of candles, incense, etc. while the 
vent-free appliance is in operation. 

15.  This is an unvented gas-fired heater. It uses air 

(oxygen) from the room in which it is installed. Provi-
sions for adequate combustion and ventilation air must 
be provided. 

16. This heater shall not be installed in a room or space 

unless the required volume of indoor combustion air is 
provided by the method described in the 

National Fuel 

Gas Code, ANSI Z223.1/NFPA 54

, the 

International 

Fuel Gas Code

 or applicable local codes.

17.  Keep room area clear and free from combustible 

materials, gasoline and other fl ammable vapors and 
liquids.

18.  Unvented gas heaters are a supplemental zone heater. 

They are not intended to be the primary heating appli-
ance. 

19. Unvented gas heaters emit moisture into the living 

area. In most homes of average construction, this 
does not pose a problem. In houses of extremely 
tight construction, additional mechanical ventilation is 
recommended. 

20.  During manufacturing, fabricating and shipping, various 

components of this appliance are treated with certain 
oils, fi lms or bonding agents. These chemicals are not 
harmful but may produce annoying smoke and smells 
as they are burned off during the initial operation of the 
appliance; possibly causing headaches or eye or lung 
irritation. This is a normal and temporary occurrence.

IMPORTANT SAFETY INFORMATION

1.  Due to high temperatures, the appliance should be 

located out of traffi c and away from furniture and 
draperies.

2.  Children and adults should be alerted to the hazard 

of high surface temperature and should stay away 
to avoid burns or clothing ignition.

3.  Young children should be carefully supervised when 

they are in the same room with the appliance. 

4.  Do not place clothing or other fl ammable material 

on or near the appliance. 

5.  Any safety screen or guard removed for servicing 

an appliance, must be replaced prior to operating 
the heater.

6.  Installation and repair should be done by a qualifi ed 

service person.

7.   To prevent malfunction and/or sooting, an unvented 

gas heater should be cleaned before use and at 
least annually by a professional service person. 
More frequent cleaning may be required due to 
excessive lint from carpeting, bedding materials, 
etc. It is imperative that control compartments, 
burners and circulating air passageways be kept 
clean.

INSTALLER

Please leave these instructions with the appliance.

OWNER

Please retain these instructions for future reference.

8.  

CARBON MONOXIDE POISONING:

 Early signs of 

carbon monoxide poisoning are similar to the fl u with 
headaches, dizziness and/or nausea. If you have these 
signs, obtain fresh air immediately. Have the heater 
serviced as it may not be operating properly.

9.  The installation must conform with local codes or, in 

the absence of local codes, with the 

National Fuel 

Gas Code, ANSI Z223.l/NFPA54.

10.  This unit complies with the latest edition of ANSI 

Z21.11.2, Unvented Heaters.

11.  Do not install the heaters in a bathroom or bedroom.

12. Correct installation of the ceramic fi ber logs, proper 

location of the heater, and annual cleaning are neces-
sary to avoid potential problems with sooting. Sooting, 
resulting from improper installation or operation, can 
settle on surfaces outside the fi replace. See log place-
ment instructions for proper installation.

WARNING

:

  •  Any change to this heater or its controls can be dangerous.

•  Improper installation or use of the heater can cause serious injury or death from fi re, burns, 

explosion or carbon monoxide poisoning.

•  Do not allow fans to blow directly into the fi replace. Avoid any drafts that alter burner fl ame 

patterns.

•  Do not use a blower insert, heat exchanger insert or other accessory, not approved for use with 

this heater where applicable.

Содержание VFI33CNI













































Отзывы: