29
10001028
RFSDV22/32/42 Freestanding Direct Vent Fireplace
This gas fireplace should be installed by a qualified installer in
accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Fireplaces and
Equipment and CAN/CSA Z 240 .4 Canada.
A manufactured home (mobile home) OEM installation must
conform with the Manufactured Home Construction and Safety
Standard,
Title 24 CFR, Part 3280, or when such a standard is not
applicable, the Standard for
Manufactured Home installations,
ANSIINCSBCS A225.1, or Standard for Gas Equipped
Recreational Vehicles and Mobile Housing CSA Z240.4.
The appliance when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes,
with the
National Electrical Code, ANSIINFPA 70, or the Canadian
Electrical Code, CSA C22.1.
For safe installation and operation please note the
following:
1 . This fireplace gives off high temperatures and should be
located out of high traffic areas and away from furniture
and draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this fireplace and should stay
away to avoid burns or ignition of clothing.
3. Children should be carefully supervised when they are in
the same room as your fireplace.
4. Under no circumstances should this fireplace be modified.
Parts removed for servicing should be replaced prior to
operating this fireplace again.
5. Installation and any repairs to this fireplace should be
carried out by a qualified service person. A professional
service person should be contacted to inspect this fireplace
annually. Make it a practice to have all of your gas
fireplaces checked annually. More frequent cleaning may
be required due to excess lint and dust from carpeting,
bedding material, etc.
6. Control compartments, burners and air passages in this
fireplace should be kept clean and free of dust and lint.
Make sure that the gas valve and pilot light are turned off
before you attempt to clean this fireplace.
7, The venting system(chimney) of this fireplace should be
checked at least once a year and if needed your venting
system should be cleaned.
8. Keep the area around your fireplace clear of combustible
materials, gasoline and other flammable vapour and
liquids. This fireplace should not be used as a drying rack
for clothing, nor should Christmas stockings or decorations
be hung in the area of it.
9. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard etc.)be used in this fireplace.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
This appliance may be installed as an OEM installation in a manufactured (mobile) home and must be installed in accordance
with the manufacturer's instrucitons and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 or
Standard for Installation in Mobile Homes, CAN/CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A converstion kit is supplied with the appliance.
For Use in Mobile Homes - Model RFSDV32RMH
11. When the fireplace is installed directly on carpeting, vinyl
tile or any combustible material other than wood, the
fireplace must be installed on a metal or wood panel
extending the full width and depth of the fireplace.
12. This fireplace requires adequate ventilation and combustion
air to operate properly.
NOTE: The RFSDV32RMH must be firmly attached to
the building.
Conversion Instructions
1. Disconnect power to the unit and shut off the gas supply.
2. Remove the glass (see "Glass Removal" section).
3. Carefully remove the logs
4. Remove the pilot assembly from bracket.
5. Remove the screws which are holding the burner housing
in place.
6. Remove the burner housing.
7. Remove the main and front orifice and replace with the
orifice supplied in the conversion kit. Use the small orifice
size for the front burner and the bigger orifice size for the
main burner.
8. Remove the compression fitting which holds the aluminum
tubing in the pilot assembly. This will reveal the pilot orifice
which must be replaced with the one provided in the
conversion kit.
9. Units with SIT valve (See pictures in the installation
instructions supplied with the kit):
a) Using a Torx T20 or slotted screwdriver, remove and
save the three pressure regulator mounting screws (A),
pressure regulator tower (B) and diaphragm (C).
b) Ensure the rubber gasket (D) is properly positioned and
install the new Hi/Lo pressure regulator to the valve
using the new screws (E) supplied with the kit. Tighten
screws securely. (Reference torque - 25 in.Lb).
c) Install the enclosed identification label (F) to the valve
body where it can be easily seen.
Units with Honeywell valve:
The Honeywell valve fitted to this unit is preset for LP
gas. It is convertible to natural gas by the installation of
a color coded "conversion screw". To insert the
conversion screw refer to the instructions and diagrams
in the Honeywell Installation Instructions supplied in the
conversion kit packaged with the RFSDV32RMH unit.
10.Reassemble the fireplace in the reverse order, except for
the front glass. Leave this off until the unit has been
checked for leaks and the gas supply line has been bled.
11.After bleeding the gas line and checking for leaks with a
soap solution, replace the front glass. Fire up the unit,
check for flame impingement on the logs, adjusting them if
necessary. Check the manifold and supply pressures.
Refer to the Troubleshooting and Parts List earlier in
this manual if further assistance is required.
