Vermont Castings Intrepid INDVR-IFT-BD Скачать руководство пользователя

Страница: 10 / 66

3-90-30007474

Vermont Castings • Intrepid DV-IFT Owner’s Manual_R20 • 11/21

Your stove is approved to be vented either through the side

wall, or vertical through the roof.

•

HHT does not require any opening for inspection of vent

pipe.

•

Only HHT SLP venting components or DuraVent venting

components specifically approved and labeled for this

stove may be used.

• Maintain minimum clearances between vent pipes and

combustible materials.

•

Venting terminals shall not be recessed into a wall or

siding.

• Any horizontal run must have a 1/4” rise for every one (1)

foot of run towards the vent termination. Never run the

vent level or down.

There must not be any

obstruction such as bushes, garden

sheds, fences, decks or utility buildings within 24" from the

front of the termination hood.
Do not locate termination hood where excessive snow or ice

build up may occur. Be sure to check vent termination area

after snow falls, and clear to prevent accidental blockage of

venting system. When using snow blowers, make sure snow

is not directed towards vent termination area.

Location of Vent Termination

It is imperative the vent termination be located observing the

minimum clearances as shown in this manual.

Содержание Intrepid INDVR-IFT-BD



































































Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды

Vermont Castings Intrepid INDVR-IFT-BD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды