Vermont Castings Intrepid INDVR-IFT-BD Скачать руководство пользователя

Страница: 32 / 66

3-90-30007474

Vermont Castings • Intrepid DV-IFT Owner’s Manual_R20 • 11/21

Existing Masonry Chimney

Prior to installing the gas stove, ensure that the existing chimney is functionally sound and clean.
• Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified

professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

• Replace component parts of the chimney and fireplace as specified by the professionals.
• See Section 11 for venting components.

Type C - Up & Out Installation

Type D - Hearth Mount

Figure 3.54

Type A & B Co-Axial to Co-Linear

Chimney Liner Termination Cap

(Included in Chimney Liner

Termination Kit)

Co-Axial to

Co-Linear Connector

(Part 46DVA-GCL)

3 in. (76mm) Flex Liner

(Included in Chimney Liner

Termination Kit)

Showing two 25 ft.

(9m) Sections of

Flex Liner

Chimney Liner Termination Cap

(Included in Chimney Liner Termination Kit)

Co-Axial to Co-Linear

Connector

(Part 46DVA-GCL)

25 ft. (9m) of 3 in. (76mm) Flex

Liner Exhaust Section

(Included in Chimney Liner Termination Kit)

4 ft. (1m) of 3 in. (76mm)

Flex Liner Air Intake Section

(Included in Chimney Liner Termination Kit)

The chimney must be sealed from the

4 ft. (1m) section to termination using

a smoke shelf or a flue restrictor. The

seal should be a minimum of 6 in.

(152mm) below the end of the 4 ft.

(1m) Air Intake section.

This section of the chimney

must be sealed

TERMINATION CAP

(Included in LINK-STOVE Kit)

FLASHING

(Included in Masonry

Chimney Conversion Kit &

LINK-STOVE Kit)

4 in. (102mm) FLEX LINER

(Included in LINK-STOVE Kit)

TOP ADAPTOR

(Included in Masonry Chimney

Conversion Kit & LINK-STOVE Kit)

RETRO CONNECTOR

(Included in Masonry Chimney

Conversion Kit & LINK-STOVE Kit)

90° ELBOW

DIRECT VENT PIPE

(Length as required)

Chimney Liner Termination Cap

(Included in Chimney Liner Termination Kit)

25 ft. (9m) of 3 in. (76mm) Flex

Liner Exhaust Section

(Included in Chimney Liner Termination Kit)

4 ft. (1m) of 3 in. (76mm) Flex

Liner Air Intake Section

(Included in Chimney Liner Termination Kit)

Chimney must be sealed

from 4 ft. (1m) section to

termination using a smoke

shelf or a flue restrictor. Seal

should be a minimum of 6 in.

(152mm) below end of 4 ft.

(1m) Air Intake section.

This section of the

chimney must be sealed

Co-Axial to Co-Linear Connector

(Part 46DVA - GCL)

Alcove Clearance to

Combustibles must be

maintained. See Figure 3.2.

See COAXIAL/COLINEAR Section and Figure 4.31.

Содержание Intrepid INDVR-IFT-BD



































































Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды

Vermont Castings Intrepid INDVR-IFT-BD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды