Vermont Castings Intrepid INDVR-IFT-BD Скачать руководство пользователя

Страница: 50 / 66

3-90-30007474

Vermont Castings • Intrepid DV-IFT Owner’s Manual_R20 • 11/21

N. Burner, Pilot & Control Compartment

Keep the control compartment, stones and burner areas

surrounding the stones clean by vacuuming or brushing at

least twice a year. Make sure the burner porting, pilot air

opening and burner air opening are free of obstructions at

all times.

Pilot Flame

The flames from the pilot should be visually checked as

soon as the heater is installed and periodically during normal

operation. The pilot flame must always be present when the

stove is in operation, Figure 4.7. The pilot flame has three

distinct flames, one engulfing the sensor, one engulfing the

thermopile, and the other reaching to the main burner.

Burner

Inspect area around the injector. Remove any lint or foreign

material with a brush or vacuum.

Burner Flame

The flames from the burner should be visually checked as

soon as the heater is installed and periodically during normal

operation. In normal operation, at full rate, and after operating

for about 15 to 30 minutes, the flame should be yellow.

NOTE: The type of installation, vent system configuration,

and wind effects may cause the flame patterns to vary.

WARNING

Turn off gas before servicing stove. It is recommended that

a qualified service technician perform these check-ups at

the beginning of each heating season

Figure 4.7

- Correct pilot and burner flame appearance.

INDVR MODELS

INDVR-IFT

LG500

Intrepid log flames

7/07

CO105d

Pilot flame

6/07 djt

Содержание Intrepid INDVR-IFT-BD



































































Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды

Vermont Castings Intrepid INDVR-IFT-BD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды