Vermont Castings Intrepid INDVR-IFT-BD Скачать руководство пользователя

Страница: 1 / 66

3-90-30007474

Vermont Castings • Intrepid DV-IFT Owner’s Manual_R20 • 11/21

Intrepid

Direct Vent Gas Heater

Model: INDVRBDSB, INDVRCBSB,

INDVR-IFT-CB, & INDVR-IFT-BD

CERTIFIED

AFETY

ARRIER

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result

in serious injury, death or property damage.

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

• WHAT TO DO IF YOU SMELL GAS

– Do not try to light any appliance.

– Do not touch any electrical switch; do not use

any phone in your building.

– Leave the building immediately.

– Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

NOTICE:

SAVE THESE INSTRUCTIONS

Installation & Operating Manual

Installation and Appliance Setup - Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Call your dealer for questions on Installation, Operation, or Service.

WARNING

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

12761
Intrepid DV Cover
6/07

DANGER

HOT GLASS

WILL

CAUSE BURNS

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this

appliance and must be installed.

Содержание Intrepid INDVR-IFT-BD



































































Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды

Vermont Castings Intrepid INDVR-IFT-BD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Intrepid INDVR-IFT-BD

Отзывы:

Похожие инструкции для Intrepid INDVR-IFT-BD

Бренды по названию

Популярные бренды