background image

20306750

61

Designer Series Direct Vent Gas Fireplace

LIMITED LIFETIME WARRANTY POLICY

LIFETIME WARRANTY

The following components are warranted for life to the original owner, subject to proof of purchase: Firebox, 

Combustion Chamber and Heat Exchanger.

FIVE YEAR WARRANTY

The following components are warranted five (5) years to the original owner, subject of proof of purchase: 

Ceramic Fiber Logs.

BASIC WARRANTY

Vermont Castings Group warrants the components and materials in your gas appliance to be free from manu

-

facturing and material defects for a period of two years from date of installation. After installation, if any of the 

components manufactured by Vermont Castings Group in the appliance are found to be defective in materials 

or workmanship, Vermont Castings Group will, at its option, replace or repair the defective components at 

no charge to the original owner. Vermont Castings Group will also pay for reasonable labor costs incurred 

in replacing or repairing such components for a period of two years from date of installation. Any products 

presented for warranty repair must be accompanied by a dated proof of purchase.
This Limited Lifetime Warranty will be void if the appliance in not installed by a qualified installer in accor

-

dance with the installation instructions. The Limited Lifetime Warranty will also be void if the appliance is not 

operated and maintained according to the operating instructions supplied with the appliance, and does not 

extend to (1) firebox/burner assembly damage by accident, neglect, misuse, abuse, alterations, negligence 

of others, including the installation thereof by unqualified installers, (2) the costs of removal, re-installation or 

transportation of defective parts on the appliance, or (3) incidental or consequential damage. All service work 

must be performed by an authorized service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty of mer

-

chantability of fitness for purpose and of all other obligations or liabilities. Vermont Castings Group does not 

assume for it any other obligations or liabilities in connection with sale or use of the appliance. It states that 

do not allow limitations on how long an implied warranty lasts, or do not allow exclusion of indirect damage, 

those limitations of exclusions may not apply to you. You may also have additional rights not covered in the 

Limited Lifetime Warranty.
Vermont Castings Group reserves the right to investigate any and all the claims against the Limited Lifetime 

Warranty and decide upon method of settlement.

IF WARRANTY SERVICE IS NEEDED:

1.  Contact your supplier. Make sure you have your warranty, your sales receipt and the model/

serial number of your Vermont Castings Group product.

2.  DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

Содержание CLLDVNSCSB

































































Отзывы: