background image

20306750

3

Designer Series Direct Vent Gas Fireplace

4.   Never install the fireplace 

 

•  

in a recreational vehicle

 

•  

where curtains, furniture, clothing, or other flam

-

mable objects are less than 42" from the front, top, 

or sides of the fireplace

 

•  

in high traffic areas

 

•  

in windy or drafty areas 

5.  This fireplace reaches high temperatures. Keep children 

and adults away from hot surfaces to avoid burns or 

clothing ignition. Fireplace will remain hot for a time after 

shutdown. Allow surfaces to cool before touching. 

6.  Young children should be carefully supervised when 

they are in the same room as the appliance. Toddlers, 

young children and others may be susceptible to acci-

dental contact burns. A physical barrier is recommended 

if there are at risk individuals in the house. To restrict 

access  to  a  fireplace  or  stove,  install  an  adjustable 

safety gate to keep toddlers, young children and other 

at risk individuals out of the room and away from hot 

surfaces. 

7.  Do not modify fireplace under any circumstances. Any 

parts removed for servicing must be replaced prior to 

operating fireplace. 

8.  Turn fireplace off and let cool before servicing, install

-

ing, or repairing. Only a qualified service person should 

install,  service,  or  repair  the  fireplace.  Have  burner 

system inspected annually by a qualified service 

person. 

9.  You must keep control compartments, burners, and 

circulating air passages clean. More frequent cleaning 

may be needed due to excessive lint and dust. Turn off 

the gas valve and pilot light before cleaning fireplace. 

10. Have venting system inspected annually by a qualified 

service person. If needed, have venting system cleaned 

or repaired. Refer to 

Cleaning and Maintenance

Page 

48.

11.  Keep the area around your fireplace clear of combus

-

tible materials, gasoline, and other flammable vapor and 

liquids. Do not run fireplace where these are used or 

stored. Do not place items such as clothing or decora-

tions on or around fireplace. 

INSTALLER

Please leave these instructions with the appliance.

OWNER

Please retain these instructions for future reference.

IMPORTANT SAFETY INFORMATION

This fireplace is a vented product. This fireplace must be 

properly installed by a qualified service person. The glass 

door must be properly seated and sealed. If this unit is not 

properly installed by a qualified service person with glass 

door properly seated and sealed, combustion leakage can 

occur. 

CARBON MONOXIDE POISONING:

 Early signs of carbon 

monoxide poisoning are similar to the flu with headaches, 

dizziness and/or nausea. If you have these signs, the fire

-

place may not have been installed properly. Get fresh air 

at once! Have the fireplace inspected and serviced by a 

qualified service person. Some people are more affected 

by carbon monoxide than others. These include pregnant 

women,  people  with  heart  or  lung  disease  or  anemia, 

those  under  the  influence  of  alcohol,  and  those  at  high 

altitudes. 
Propane/LP gas and natural gas are both odorless. An 

odor-making agent is added to each of these gases. The 

odor helps you detect a gas leak. However, the odor added 

to these gases can fade. Gas may be present even though 

no odor exists.

Make certain you read and understand all warnings. Keep 

this manual for reference. It is your guide to safe and proper 

operation of this fireplace.
1.  This  appliance  is  only  for  use  with  the  type  of  gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases unless a certified 

kit is used. 

2.  For  propane/LP  fireplace,  do  not  place  propane/LP 

supply tank(s) inside any structure. Locate propane/LP 

supply tank(s) outdoors. To prevent performance prob-

lems, do not use propane/LP fuel tank of less than 100 

lbs. capacity. 

3.  If you smell gas

  shut off gas supply.

  do not try to light any appliance.

•  

do not touch any electrical switch; do not use any 

phone in your building .

•  

immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

• 

Read this owner’s manual carefully and completely before trying to assemble, operate, or service this 

fireplace. 

• 

Any change to this fireplace or its controls can be dangerous.

• 

Improper  installation  or  use  of  this  fireplace  can  cause  serious  injury  or  death  from  fire,  burns, 

explosions, electrical shock and carbon monoxide poisoning.

W

ARNING

Содержание CLLDVNSCSB

































































Отзывы: