background image

8

VCG Royalton Series • BE36/42 • 4044-197 Installation Manual • Rev A •  02/18/15

C. Tools and Supplies Needed

Before beginning the installation be sure the following 

tools and building supplies are available:
Reciprocating saw 

Framing material

Pliers 

Non-combustible sealant

Hammer 

Gloves

Phillips screwdriver 

Framing square

Flat blade screwdriver 

Electric drill and bits

Plumb line 

Safety glasses

Level 

Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws
Misc. screws and nails

D. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! 

Damaged 

parts could impair safe operation. 

DO NOT

 install dam-

aged, incomplete or substitute components. Keep fire

-

place dry.

•  Remove fireplace and components from packaging and 

inspect for damage.

•  Vent  system  components  and  doors  are  shipped  in 

separate packages.

•  Report to your dealer any parts damaged in shipment.

•  Read  all  the  instructions  before  starting  the 

installation. Follow these instructions carefully 

during the installation to ensure maximum safety 

and benefit.

E. Fireplace System Requirements

The VCG fireplace system requirements consist of the 

following:
•  Fireplace

-  Refractory (included with fireplace)

-  Firescreen (included with fireplace)

-  Grate (included with fireplace)

-  Hearth Extension (required, sold separately)

•  Outside Air System (optional)

-  Air Inlet Hood

-  Flex

•  Chimney System

-  Attic Insulation Shield (included with fireplace)

-  Chimney air kit (required in Canada, sold separately)

-  Chimney termination cap (required, sold separately)

•  Non-combustible finish material

Содержание BE36








































Отзывы: