Vermont Castings BE36 Скачать руководство пользователя страница 12

Страница: 12 / 39

VCG Royalton Series • BE36/42 • 4044-197 Installation Manual • Rev A • 02/18/15

D. Frame the Fireplace

NOTICE:

Hearth extension design must be determined

before installation of fireplace.

If the fireplace is placed on the floor the maximum height

of a finished raised hearth is 7 1/2”. If you want a higher

raised hearth the fireplace must be placed on a platform.

WARNING! Risk of Fire!

You must comply with all

minimum air space clearances to combustibles.

DO NOT

pack required air spaces with insulation or other materi

als.

WARNING! Risk of Fire!

Comply with all minimum clear-

ances specified.
• A minimum 1/2 in. (13 mm) air clearance must be

maintained at the back and sides of the fireplace

assembly.

•

Chimney sections at any level require a 2 in. (51

mm) minimum air space clearance between the

framing and chimney section.

Figure 3.5 shows a typical framing (using 2 x 4 lumber)

of the fireplace, assuming combustible materials are

used. All required clearances to combustibles around the

fireplace must be adhered to. See Figure 3.2. Any framing

across the top of the fireplace must be above the level of

the top standoffs.

CAUTION!

Risk of Cuts/Abrasions. Wear protective gloves

and safety glasses during installation. Sheet metal edges

are sharp.

WARNING! Risk of Fire!

Prevent contact with sagging,

loose insulation.

•

DO NOT

install against vapor barriers or exposed

insulation.

• Secure insulation and vapor barriers.

• Provide minimum air space clearances at the sides and

back of the fireplace assembly.

E. Secure and Level the Fireplace

This fireplace may be placed on either a combustible or

noncombustible continuous flat surface. Follow the instruc

tions for framing in Section 3. Slide the fireplace into posi

tion. Be sure to provide the minimum 1/2 in. air clearance

at the sides and back of the fireplace.
The fireplace should be positioned so the face of the non-

combustible material on the fireplace will be flush with the

face of the drywall on the walls.
Level the fireplace and shim as necessary.

2 in. (51 mm)

min. air space

clearance

from chimney.

Header MUST NOT be notched!

D = extra space needed for outside air connection.
If outside air duct has no bend, this dimension may be
reduced as long as minimum clearances are met.

Model

C**

in.

21 1/2

39 3/4

1067

546

1010

203

in.

21 1/2

39 3/4

1219

546

1010

203

BE-36

BE-42

* If interior of chase will be drywalled, add the thickness to
** Adjust header height for a raised floor under fireplace.

Figure 3.5 Framing the Fireplace

1/2 in.

(13 mm)

Fireplace must be set out

1/2 in. (13 mm) in front of

the face of the framing

material.

The finished cavity depth must be no less than 21 3/8 in.

(543 mm) from the finished backwall to the outside of front

wall framing.

WARNING! Risk of Fire.

A raised hearth extension built

flush with the fireplace opening or less than 4 in. (102

mm) below the fireplace opening requires the fireplace be

installed on a non-combustible surface.

Содержание BE36








































Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды

Vermont Castings BE36, Руководство по установке

Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды