Vermont Castings BE36 Скачать руководство пользователя страница 30

Страница: 30 / 39

VCG Royalton Series • BE36/42 • 4044-197 Installation Manual • Rev A • 02/18/15

C. Non-Combustible Sealant Material

After completing the framing and applying the facing

materials over the framing, a bead of noncombustible

sealant must be used to close off any gaps at the top

and sides between the fireplace and hearth.

Non-combustible Sealant

Figure 7.9 Place Non-combustible Sealant

3. Fireplace Opening and Hearth Extension

Flush with the Floor

Non-combustible flooring a minimum of 20 in. (762 mm)

in front of and 12 in. (305 mm) to each side of the fuel

opening is required.

The hearth framing must be constructed of non-

combustible materials (such as metal framing or

equivalent material) and placed on HX3(s), HX4(s), or

equivalent material.

When creating the platform, allow for the thickness

of the non-combustible finishing materials

Seal gaps between the hearth extension and the front

of the fireplace with a bead of non-combustible sealant

or grout.

Noncombustible Material

Protective Metal

Hearth Strip

20 in. Min.

Hearth Extension

Micore

Finished

Floor

Note: The bottom of the

fireplace opening is 7 1/2 in.

(191 mm) above the bottom

of the fireplace. Finished

hearth must NOT extend

above this level.

Non-combustible

material must be

used under the

fireplace if top of

hearth is less than

4 in. (103 mm)

below the

fireplace opening.

Figure 7.8 Flush Hearth Extension Side View

Содержание BE36








































Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды

Vermont Castings BE36, Руководство по установке

Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды