Vermont Castings BE36 Скачать руководство пользователя страница 3

Страница: 3 / 39

VCG Royalton Series • BE36/42 • 4044-197 Installation Manual • Rev A • 02/18/15

Customer:

Lot/Address

Model (circle one):

BE36
BE42

YES

IF NO, WHY?

WARNING! Risk of Fire or Explosion!

Failure to install fireplace acording to these instructions can lead to a fire or

explosion.

Verified that the chase is insulated and sealed. (Pg. 11)
Verified clearances to combustibles. (Pg. 10)
Fireplace is leveled and secured. (Pg. 12)

Hearth extension size/height decided. (Pg. 28)

Chimney configuration complies with diagrams.
Chimney installed, locked and secured in place with proper clearance.
Chimney air kit installed.
Firestops installed.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation

manual.

Date Installed:

Location of Fireplace:

Installer:

Protective hearth strips installed per manual requirements. (Pg. 13)

Fireplace Install

Outside air kit installed. (Pg 14)

Chimney Section 4 & 5 (Pg. 15)

Attic insulation shield installed.

Shrouds Section 6 (Pg. 25)

Shroud is installed properly per instructions.

Fi i hi

S ti

7 (P 27)

Dealer/Distributor Phone #

Serial #:

Roof flashing installed.
Termination installed.

Vermont Castings Group recommends the following:

Comments communicated to party responsible

4044-199 • Rev A • 2-18-15

__________________________ by ______________________on _________
(Builder/Gen. Contractor) (Installer) (Date)

Comments:

Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Manual bag and all of its contents are removed from the fireplace and given to the party

responsible for use and operation.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

• Photographing the installation and copying this checklist for your file.

Combustible materials not installed in non-combustible areas.

Finishing Section 7 (Pg. 27)

Hearth extension installed per manual requirements.

Fireplace Setup Section 8 (Pg. 34)

All packaging and protective materials removed.

Optional doors properly installed.

Refractory installed correctly.
Grate is properly installed.

Verified all clearances meet installation manual requirements.
Mantels and wall projections comply with installation manual requirements.

Firescreen properly installed.

Содержание BE36








































Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды

Vermont Castings BE36, Руководство по установке

Результаты поиска

Содержание BE36

Отзывы:

Похожие инструкции для BE36

Бренды по названию

Популярные бренды