Venture Products Ventrac SS575 Скачать руководство пользователя

Страница: 22 / 53

SPREADER SETUP & INSTALL KITS

Setup - 22

15. Connect the battery/controller wire harness and

the motor/controller wire harness to the spreader

controller and route the harnesses back along the

control box mount arm and down along the roll bar.

16. Use Velcro ties to fasten both wire harnesses

to the arm of the control box mount just behind

the controller and also to fasten the harnesses

together, but not to the control box arm, about

halfway back to the roll bar.

17. Leave a small amount of slack in the wire harnesses

and use Velcro ties to fasten the harnesses to the

roll bar just below the frame mount bracket and right

above the power unit fender as shown above.

18. Connect the motor/controller harness to the

power cord on the spreader and coil the extra

wire at the corner of the right fender. Use a Vel-

cro tie to fasten both harnesses to the power unit

seat box. Fasten the coils of the motor/controller

harness together using a Velcro tie.

19. Cut the push-on connectors off the end of the

battery/controller wire harness and strip 1/4” of

insulation off the end of each wire.

20. Locate the adapter harness plug with red and black

wires. Insert the red wire from the battery/controller

harness into the butt connector on the red wire (M)

from the adapter harness and crimp in place. Insert

the black wire from the battery/controller harness

into the butt connector on the black wire (N) from

the adapter harness and crimp in place.

21.

Slide the heat shrink tube (O) over the butt con-

nectors and use a heat gun to shrink in place.

22. If the spreader is being used without a vibrator, fold

the white and black wire with butt connectors back

along the connector and harness and tape in place.

23. Coil the extra wire of the battery/controller har-

ness inside the seat box area and use a Velcro

tie to fasten the coils together.

24. Install the 25 amp circuit breaker into slot 1 of

the rear fuse panel and the 10 amp fuse into slot

3 of the rear fuse panel.

25. Remove the cover from the power relay module

and replace both J-case fuses (P) with the sup-

plied 60 amp J-case fuses.

26.

Connect the negative battery cable to the battery.

27.

Use the #10-32 x 1-1/2” screw and flange nut to

attach the tether on the spreader’s power cord

cap to the plug on the power cord.

Installation is complete.

Содержание Ventrac SS575






















































Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды

Venture Products Ventrac SS575, Руководство оператора и чертежи запасных частей

Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды