Venture Products Ventrac SS575 Скачать руководство пользователя

Страница: 13 / 53

Setup - 13

SPREADER SETUP & INSTALL KITS

SS575 Install 4100/4200 Kit

Document Number

Kit Number / Part Number

Model

Serial Number Range

09.700131

70.8113

SS575

All Units

Tools Required:

3/8” wrench

7/16” wrench*

1/2” wrench

9/16” socket*

3/4” socket

impact driver

7/32” drill bit*

drill* phillips screwdriver

side cut pliers

Before making repairs or adjustments set the parking

brake, turn off engine, and remove ignition key.

Always disconnect the negative battery cable from the

battery when working with electrical components. Always

work in a manner that does not put safety at risk!

Safety glasses must be worn during installation.

Ear (hearing) protection must be worn when

using air or power tools.

Installation Time (estimated)

1 hour

Installation Notes:

Right and left hand orienta

tion referred to in these instructions is determined

as if sitting on the tractor seat, facing forwards.

*Not necessary for all setup configurations.

1. Disconnect the negative battery cable from the

power unit’s battery.

2. Remove the nut and bolt from the positive and

negative battery cable clamps and replace them

with 5/16” x 1-1/2” bolts and nuts. Tighten the

positive clamp onto the positive battery terminal.

3. Install the fused positive wire onto the positive

cable clamp bolt and fasten with a 5/16” nut.

4. Install the negative cable onto the negative terminal

and tighten. Install the negative wire onto the nega-

tive cable clamp bolt and fasten with a 5/16” nut.

5. Using a side cut pliers, cut both battery terminal

covers at the locations shown and install onto

the battery terminals.

Cut Here

6. Install the spreader hitch onto the spreader using

4) 1/2” x 1-1/4” bolts and 4) 1/2” flat washers. Use

Loctite 242 or equivalent thread locker on bolts.

Torque to 45 ft-lbs (61 Nm).

7. Fasten the spreader’s power cord to the hitch

frame at two places using zip ties.

Содержание Ventrac SS575






















































Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды

Venture Products Ventrac SS575, Руководство оператора и чертежи запасных частей

Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды