Venture Products Ventrac SS575 Скачать руководство пользователя

Страница: 11 / 53

SAFETY

Safety - 11

General Safety Procedures

for Ventrac Power Units, Attachments, & Accessories

•

Do not overfill fuel tank. Only fill to bottom of fuel neck, do not fill fuel neck full. Overfilling of fuel tank could

result in engine flooding, fuel leakage from the tank, and/or damage to the emissions control system.

• If fuel is spilled, do not attempt to start the engine. Move the power unit away from the fuel spill and

avoid creating any source of ignition until fuel vapors have dissipated.

• If the fuel tank must be drained, it should be drained outdoors into an approved container.

•

Dispose of all fluids in accordance with local laws.

• Check all fuel lines for tightness and wear on a regular basis. Tighten or repair them as needed.

• The fuel system is equipped with a shut-off valve. Shut off the fuel when transporting the machine to

and from the job, when parking the machine indoors, or when servicing the fuel system.

Hydraulic Safety

• Make sure all hydraulic connections are tight and all hydraulic hoses and tubes are in good condition.

Repair any leaks and replace any damaged or deteriorated hoses or tubes before starting the machine.

• Hydraulic leaks can occur under high pressure. Hydraulic leaks require special care and attention.

• Use a piece of cardboard and a magnifying glass to locate sus-

pected hydraulic leaks.

• Keep body and hands away from pinhole leaks

or nozzles that eject high pressure hydraulic fluid.

Hydraulic fluid escaping under high pressure can

penetrate the skin causing serious injury, leading to

severe complications and/or secondary infections

if left untreated. If hydraulic fluid is injected into the

skin, seek immediate medical attention no matter

how minor the injury appears.

• Hydraulic system may contain stored energy. Before performing maintenance or repairs on the hydraulic

system, remove attachments, engage parking brake, disengage weight transfer system (if equipped), shut

off engine, and remove ignition key. To relieve pressure on the auxiliary hydraulic system, shut off the power

unit engine and move the secondary S.D.L.A. lever left and right before disconnecting the auxiliary hydraulic

quick couplers.

•

Dispose of all fluids in accordance with local laws.

Fuel Safety (continued)

Содержание Ventrac SS575






















































Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды

Venture Products Ventrac SS575, Руководство оператора и чертежи запасных частей

Результаты поиска

Содержание Ventrac SS575

Отзывы:

Похожие инструкции для Ventrac SS575

Бренды по названию

Популярные бренды