Venture Products Ventrac SS575 Скачать руководство пользователя страница 32

Страница: 32 / 53

Operation - 32

GENERAL OPERATION

Daily Inspection

Always set the parking brake, shut off power

unit engine, remove the ignition key, and ensure

all moving parts have come to a complete stop

before inspecting components, or attempting

any repair or adjustment.

Park machine on a level surface, with the engine

shut off and all fluids cold.

2. Perform a visual inspection of both the power unit

and the spreader. Look for loose or missing hard-

ware, damaged components, or signs of wear.

3. Be sure all electrical connections are tight and

clean.

4. Be sure nothing is jammed in the hopper.

5. Refer to the power unit operator’s manual.

Check the power unit’s engine oil, hydraulic oil,

cooling system, tire pressure, and fuel level. Add

fluid or service as required.

6. Test the power unit’s operator safety interlock

system*.

Spreader Loading

Do not overload spreader or power unit. Use the

chart below to calculate weight of material. Weights

of material are an average for dry materials.

Material

Weight Per Cubic Ft.

Rock Salt

75-85 lbs. (34-38.5 kg)

Sand/Salt Mix

95-120 lbs. (43-54.5 kg)

Maximum Spreader Capacity (Volume) 5.75 ft

(.163 m

)

Maximum Spreader Capacity (Weight) 460 lbs. (209 kg)

Use the following charts to determine the allowable

weight capacity of the spreader in combination with

various power unit and attachment setups.

After loading material into spreader hopper, replace

the hopper cover and latch securely.

Spreader Operation

* Refer to power unit operator’s manual for operation of

power unit controls.

Ventrac 4100 and 4200 (without cab)

Attachment On Front Of Power Unit

SS575 Capacity

HE480

48” Slip Scoop

300 lbs (136 kg)

HJ480

48” Excavator

300 lbs (136 kg)

KD482

48” Dozer Blade

300 lbs (136 kg)

KD602

60” Dozer Blade

350 lbs (159 kg)

KD722

72” Dozer Blade

350 lbs (159 kg)

KV522

55” V-Blade

400 lbs (181 kg)

HB580

58” Broom

460 lbs (209 kg)

KX523

52” Snowblower

460 lbs (209 kg)

Ventrac 4100 and 4200 (with KW350 Cab)

Attachment On Front Of Power Unit

SS575 Capacity

HE480

48” Slip Scoop

150 lbs (68 kg)

HJ480

48” Excavator

150 lbs (68 kg)

KD482

48” Dozer Blade

150 lbs (68 kg)

KD602

60” Dozer Blade

200 lbs (91 kg)

KD722

72” Dozer Blade

200 lbs (91 kg)

KV522

55” V-Blade

250 lbs (113 kg)

HB580

58” Broom

460 lbs (209 kg)

KX523

52” Snowblower

460 lbs (209 kg)

The rear weights must be removed from the power unit.

Weight transfer set to 100%.

Exceeding the listed weight capacities in the

following charts may result in loss of steering or

front wheel traction.

Sweep area clear of foreign objects or obstacles

that could cause personal injury.

Keep other persons, children, or animals out of

the area to be spread.

If there are any problems while operating the

spreader, refer to the Troubleshooting Guide.

Never leave materials in hopper for long periods

of time, as ice melt products are hygroscopic and

will attract atmospheric moisture and harden.

Do not operate power unit with SS575 spreader

on slopes greater than 10 degrees. Operation on

slopes greater than 10 degrees may result in loss

of steering or front wheel traction.

Содержание Ventrac SS575






















































Результаты поиска

Содержание Ventrac SS575

Отзывы:

Бренды по названию

Популярные бренды

Venture Products Ventrac SS575, Руководство оператора и чертежи запасных частей

Результаты поиска

Содержание Ventrac SS575

Отзывы:

Бренды по названию

Популярные бренды