Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

Velatia ORMAZABAL gae.630 Скачать руководство пользователя страница 20

IG-322-EN version 03; 22/07/2022

20

Transport and installation

General instructions

SF

6

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

3.7. Installation of the supply line for the auxiliary and control circuits

There are openings for laying the supply line for the auxiliary

and control circuits in the roof of the relay cabinet.

Flexible plugs are fitted in these openings, which provide

a cable bushing protected against dust and moisture. For

adaptation to the cable diameter use the separating lines

on the plugs.

The supply line from a neighbouring panel on the left or

right (loop cable) is laid through openings in the related

side wall on the relay cabinet (Figure 3.9).

If the relay cabinet on the neighbouring panel is fitted

offset, the cable can be laid through the openings in the

roof of the relay cabinet (Figure 3.10).

1

2

1

Openings in the roof

2

Openings in the side wall

Figure 3.9.

Relay cabinet flush at the rear wall

1

1

Openings in the roof

Figure 3.10.

Relay cabinet offset

«
...
18
19
20
21
22
...
»

Содержание ORMAZABAL gae.630

































































Отзывы:

Нет отзывов