Veit SF26 страница 27 Скачать руководство пользователя

Страница: 27 / 149

4.1 Danger zone of the machine

The operator has access to the following parts of the machine:

1 Machine

2 Operating area

3 Danger zones during commissioning, servicing, maintenance

and repair

4.2 Duties of the operating company

The operating company has to obtain the operating license and

must observe the associated obligations.
In addition, the company has to comply with the local regulations

Safety of personnel (accident prevention regulations)

Safety of equipment (protective equipment and maintenance)

Disposal of products (waste management law)

Disposal of materials (waste management law)

Cleaning (cleaning agents and disposal)

Environmental obligations

NOTICE!

Prior to commissioning the machine, the operating

company must ensure that the local regulations,

e.g. on electric and pneumatic connections, are

complied with if the company itself is responsible

for setup and installation.

Potential dangers

Duties of the operating company

18.07.2017

Shirt finisher VEIT SF26

Содержание SF26






















































































































































Результаты поиска

Содержание SF26

Отзывы:

Похожие инструкции для SF26

Бренды по названию

Популярные бренды

Veit SF26, Руководство по эксплуатации

Результаты поиска

Содержание SF26

Отзывы:

Похожие инструкции для SF26

Бренды по названию

Популярные бренды