Veit SF26 страница 44 Скачать руководство пользователя

Страница: 44 / 149

7.2 Operating state of the machine

7.2.1 Operating state

Machine in home position

All tensioning elements are open

Carriage in lower position

No automatic mode (pedal not pressed)

No finishing cycle active

Machine in idle state

All tensioning elements are open

No automatic mode (pedal not pressed)

No finishing cycle active

7.2.2 Run to home position

Pressing the "stop" button when the machine is in idle state starts

the run to home position. The following sequence is started and

run through automatically.

All tensioning elements open

Fan off and steam valve closed

Carriage moves down until the lower reed switch is triggered

The machine is in home position.

7.2.3 Run to reference position

After the control system has been started, pressing the "reference

start" button starts the run to reference position. The following

sequence is started and run through automatically.

All tensioning elements open

Fan off and steam valve closed

The light barrier for hem detection is checked for validity.

The carriage moves up until the upper reed switch is triggered

and then down until the lower reed switch is triggered. After

successful completion of the reference run, the machine is in

home position and ready to operate.

Operation

Operating state of the machine > Run to reference position

18.07.2017

Shirt finisher VEIT SF26

Содержание SF26






















































































































































Результаты поиска

Содержание SF26

Отзывы:

Похожие инструкции для SF26

Бренды по названию

Популярные бренды

Veit SF26, Руководство по эксплуатации

Результаты поиска

Содержание SF26

Отзывы:

Похожие инструкции для SF26

Бренды по названию

Популярные бренды