Vega VEGAPULS 69 Скачать руководство пользователя страница 61

Страница: 61 / 100

8 Diagnosis, asset management and service

VEGAPULS 69 • Modbus and Levelmaster protocol

47252-EN-210205

Out of specification:

The measured value is unreliable because an

instrument specification was exceeded (e.g. electronics temperature).

This status message is inactive by default.

Maintenance required:

Due to external influences, the instrument

function is limited. The measurement is affected, but the measured

value is still valid. Plan in maintenance for the instrument because a

failure is expected in the near future (e.g. due to buildup).
This status message is inactive by default.

Code
Text message

Cause

Rectification

F013
no measured value

available

Sensor does not detect an echo during

operation
Antenna system dirty or defective

Check or correct installation and/or pa

rameter settings
Clean or exchange process component

or antenna

F017
Adjustment span too

small

Adjustment not within specification

Change adjustment according to the limit

values (difference between min. and max.

≥ 10 mm)

F025

Error in the lineariza

tion table

Index markers are not continuously rising,

for example illogical value pairs

Check linearization table
Delete table/Create new

F036
No operable software

Failed or interrupted software update

Repeat software update
Check electronics version
Exchanging the electronics
Send instrument for repair

F040
Error in the electronics

Hardware defect

Exchanging the electronics
Send instrument for repair

F080
General software error

General software error

Disconnect operating voltage briefly

F105
Determine measured

value

The instrument is still in the switch-on

phase, the measured value could not yet

be determined

Wait for the end of the switch-on phase
Duration up to approx. 3 minutes depend-

ing on the version and parameter settings

F113
Communication error

EMC interference

Remove EMC influences

F125
Impermissible electron-

ics temperature

Temperature of the electronics in the non-

specified range

Check ambient temperature
Insulate electronics
Use instrument with higher temperature

range

F260
Error in the calibration

Error in the calibration carried out in the

factory
Error in the EEPROM

Exchanging the electronics
Send instrument for repair

F261
Error in the instrument

settings

Error during setup
False signal suppression faulty
Error when carrying out a reset

Repeat setup
Carry out a reset

Failure

Содержание VEGAPULS 69





































































































Результаты поиска

Содержание VEGAPULS 69

Отзывы:

Похожие инструкции для VEGAPULS 69

Бренды по названию

Популярные бренды

Vega VEGAPULS 69, Руководство по эксплуатации

Результаты поиска

Содержание VEGAPULS 69

Отзывы:

Похожие инструкции для VEGAPULS 69

Бренды по названию

Популярные бренды